User manual PLANTRONICS CA10

[. . . ] Reason for return and description of the problem Damage occurring during shipment is deemed the responsibility of the carrier, and claims should be made directly with the carrier. Try our Fax-on-Demand Information Services at: Tel. (800) 544-4660 (Prompt #4) The name Plantronics and the Plantronics logo are registered trademarks of Plantronics, Inc. Quick Disconnect is a trademark of Plantronics, Inc. 17 CA 10_1 12/12/01 3:46 PM Page 9 CA 10_1 NO POSTAGE NECESSARY IF MAILED IN THE UNITED STATES 12/12/01 BUSINESS REPLY MAIL FIRST - CLASS MAIL PERMIT NO. 51 BREA CA POSTAGE WILL BE PAID BY ADDRESSEE 3:46 PM Page 10 PLANTRONICS PO BOX 9367 BREA CA 92822-8881 CA 10_1 12/12/01 3:46 PM Page 11 WELCOME Thank you for selecting the CA10 Cordless Telephone Headset Amplifier from Plantronics. [. . . ] Observe proper orientation between battery pack and charger contacts. SAVE THESE INSTRUCTIONS 5 CA 10_1 12/12/01 3:46 PM Page 16 STEP 1 SETUP Connect the CA10 Amplifier to your telephone using the illustrations on page ii. Unplug the telephone handset from the jack on your telephone base and insert into the Handset Jack 26 on the underside of the CA10 Base Unit. Using the Short Cord 28 provided, plug one end into the CA10 Telephone Jack 27 and the other end into your telephone's handset jack. Now connect the AC Adapter 23 to the AC Adapter Jack 24 and into a wall outlet. The Power LED 13 will light after connected, but the In-Use Indicator Light 14 will remain off. Make sure you remove the shipping battery insulator pull tab located between the Remote Unit and the Battery Pack. The Remote and Battery Pack slip together easily and gently snap in place. If you are using a headset whose cable terminates in a Quick DisconnectTM (QD) module, you will need the QD to 2. 5mm Headset Adapter Cable 11 (P/N 43446-02). Firmly slide the Remote Unit and Battery Pack into the Charging Well 19 until the Charge Indicator 15 lights. A G B C 6 CA 10_1 12/12/01 3:46 PM Page 17 Note: Remote Unit must remain in the Base for 5 seconds to establish a communications link before the system can function. Prior to first use, the Battery must charge for 8 hours before the Remote will operate away from the Base. (Note: May increase charging time. ) The Charge LED will turn off after the Battery is fully charged. You are now ready to make or receive calls. 7 CA 10_1 12/12/01 3:46 PM Page 18 STEP 2 PLACING A CALL With your headset in position, place the handset off-hook. The In-Use Indicator Lights 1 14 on the Remote and Base Unit will light and you will hear a dial tone. Flashes for 2 seconds while verifying contact when Remote is placed in Base Unit Charging Well. Remains steady while charging, off when battery is fully charged. AUDIO Low Battery -- Two (2) beeps generated at 30 second intervals whenever power is low, heard only through the headset in TALK mode. Out-of-Range -- Three (3) beeps generated whenever the Remote is taken out-of-range of the Base, heard only in TALK mode through the headset. Linked -- One (1) beep heard through the headset whenever the Base or Remote Unit TALK button is activated. Ringer Tone Alert -- (Can be activated when using optional Handset Lifter) Tone emitted by Remote timed with telephone ringer; can be disabled using Ringer Switch on Remote. (Note: Disabling the audible ringer does not disable the Page Function or the ringing heard through the headset. ) 11 CA 10_1 12/12/01 3:46 PM Page 22 TROUBLESHOOTING I CANNOT HEAR A DIAL TONE Make sure your Remote Battery Pack is securely seated in the Charging Well and/or fully charged. Pay special attention that Handset and Telephone cords are properly connected. Return the Remote to the Base Unit charger for 5 seconds to re-establish a communication link. A C C G MY REMOTE STOPPED WORKING Separate and then reconnect the Battery pack and Remote Unit. Return the Remote Unit to the Charging Well for 5 seconds to re-establish a communication link. C A CALLER CANNOT HEAR MY VOICE Make sure the Mute 9 Button is off. Make sure Transmit Level Switch 20 is in position 1 or 2. [. . . ] Any condition caused by accident, abuse, misuse or improper operation, violation of instructions furnished by Plantronics, destruction or alteration, improper electrical voltages or currents, or repair or maintenance attempted by anyone other than Plantronics or an authorized service center, is not a defect covered by this Warranty. In such cases, Plantronics may charge you for materials and labor, even during the warranty period. Parts subject to wear and tear in normal usage are not covered by the Warranty. Implied Warranties Under state law, you may be entitled to the benefit of certain implied warranties. [. . . ]