User manual PLANTRONICS .AUDIO 630M PC HEADSET DECLARATION OF CONFORMITY

[. . . ] 12 Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 EN iii Important Note on Wireless Range The . Audio 995 headset has a wireless range of up to 40 feet. However, wireless performance may be affected by nearby objects including walls, metal items, and other wireless devices. When you move the headset to the edge of its wireless range, audio may become distorted and will eventually cut out. [. . . ] Using Your Headset 1 2 3 Make sure that your headset is fully charged. After removing your headset from the charger, press the Power button to turn the headset on. The headset and the adapter should connect immediately, and the indicator lights on both headset and wireless adapter will be solid blue. If you cannot hear anything through your headset, try adjusting the volume up or restarting the media application. Note If steps 1 through 3 do not work, refer to "Pairing Your Headset" on page 4 to manually pair your headset and adapter. EN 3 Pairing Your Headset How to Manually Pair Your Headset and Adapter Your headset and adapter are factory pre-paired, and should automatically connect with each other. Should your headset and adapter become unpaired, you can initiate pairing manually: 3 4 Turn headset off Single press the Connect/Pair button on the adapter, then repeat steps 1 and 2. 1 Press and hold the Power and Connect buttons on the headset and adapter for 4 seconds. If the pairing is successful the status lights will glow solid blue; if unsuccessful, both headset and adapter will stay in pairing mode. 2 Note If your headset and adapter are separated and lose their connection after being successfully paired, they will automatically reconnect when they come back into range of each other. If they remain out of range for more than 30 seconds, the headset will go into sleep mode, but will reconnect automatically with the adapter once it is back in range. If the headset is out of range for more than 15 minutes, it automatically shuts off. If manual pairing was unsuccessful, and you want to re-attempt the pairing process, you must first take your headset and adapter out of pairing mode. 4 Headset Controls Adjust volume Increase: Press + Decrease: Press Minimum volume: Continually press Mute speakers: Press WARNING Do not use headsets at high volumes for an extended period of time. plantronics. com/healthandsafety for more information on headsets and hearing. Note Some applications, such as iTunes, must be the active window in order for play, pause and skip to work properly. EN 5 Operating Systems Configuration Your . Audio 995 headset works with any USBcompliant computer. The headset will automatically be set as the active audio device once the wireless USB Adapter is plugged in. Some media applications, when embedded in a web page, do not recognize standard Windows audio commands for play/pause and/or track/skip. When using the internet to make calls (i. e. , using VoIP), callers cannot hear me. Check that the application being used has "Plantronics Wireless Device" listed as the active device for listening and speaking. Some applictions need to be set manually or restarted before they will recognize a new audio device. Note: In unusual circumstances the headset may switch off. Switch the headset back on to resume normal operation. EN 11 Regulatory Notices FCC ReqUIReMeNtS PARt 15 Operation is subject to the following two conditions: 1. This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] Any unauthorized modification to the antenna or device could void the user's authority to operate this device. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. Industry Canada Radio equipment The term "IC:" before the radio certification number only signifies that Industry Canada technical specifications were met. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. [. . . ]