User manual PLANAR PX2491W

[. . . ] User's Guide PX2491W Make sure to read the Important Precautions before using the product. Keep the User's Guide(CD) in an accessible place for future reference. See the label attached on the product and give the information to Planar's customer service representative should you require assistance. Important Precautions This unit has been engineered and manufactured to ensure your personal safety, however improper use may result in potential electrical shock or fire hazards. In order to allow the proper operation of all safeguards incorporated in this display, observe the following basic rules for its installation, use, and servicing. On Safety Use only the power cord supplied with the unit. If you use another power cord, make sure that it is certified by the applicable national standards when not provided by the supplier. [. . . ] Click on the [True Color Finder] -> [Installation] icons to install the program. For detailed method on how to use the program, refer to the True Color Finder manual in the provided CD. You can unlock the OSD controls at any time by pushing the MENU button for several seconds. The message "OSD UNLOCKED" should appear. 15 Control Panel Functions Buttons Use these buttons to select or adjust functions in the On Screen Display. Press the AUTO/SET button to MUTE ON and press it once again to MUTE OFF. (Only for HDMI input) MUTE OFF Use the MUTE ON buttons to adjust the volume. (SOURCE Hot key) When two or more input signals are connected, you can select the input signal (DVI-I/DVI-D/HDMI) you want. The default input signal is DVI-I (analog). AUTO/SET Button Use this button to enter a selection in the On Screen Display. AUTO IMAGE ADJUSTMENT When adjusting your display settings, always press the AUTO/SET button before entering the On Screen Display(OSD). (Only for DVI-I analog signal cable input) This will automatically adjust your display image to the ideal settings for the current screen resolution size (display mode). The best display mode is 1920 x 1200 Power Button Power Indicator Use this button to turn the display on or off. The power indicator stays red if the display is running properly (On Mode). If the display is in Sleep Mode (Energy Saving), the power indicator is blinking red. 16 On Screen Display (OSD) Control Adjustment Screen Adjustment Making adjustments to the image size, position and operating parameters of the display is quick and easy with the On Screen Display Control system. A short example is given below to familiarize you with the use of the controls. The following section is an outline of the available adjustments and selections you can make using the OSD. To make adjustments in the On Screen Display, follow these steps: Pops up the menu screen Move where you want to adjust Select a menu icon Adjust the status Exit from the menu screen. 1 2 3 4 Press the MENU Button, then the main menu of the OSD appears. When the icon you want becomes highlighted, press the AUTO/SET Button. Press the MENU Button once to return to the main menu to select another function. Press the MENU Button twice to exit from the OSD. 17 On Screen Display(OSD) Selection and Adjustment The following table indicates all the On Screen Display control, adjustment, and setting menus. DVI-I(A) : DVI-I(Analog) signal DVI-I(D) : DVI-I(Digital) signal DVI-D HDMI(Y) : HDMI (YUV) signal HDMI(R) : HDMI (RGB) signal : DVI-D(Digital) signal Main menu Sub-menu CUSTOM Supported signals DVI-I(A) DVI-I(D) DVI-D HDMI(Y) HDMI(R) DVI-I(A) DVI-I(D) DVI-D HDMI(R) DVI-I(A) DVI-I(D) DVI-D HDMI(R) DVI-I(A) DVI-I(D) DVI-D Description The default mode that adjusts the overall range of colors of the RGB LED panel. COLOR MODE sRGB Adjusts colors based on sRGB. ADOBE RGB Adjusts colors based on ADOBE RGB. CALIBRATION Adjusts Color features by controlling the Brightness, WhitePoint and Gamma values through the color management system (CMS). Adjusts Color features by controlling the Brightness, WhitePoint , RGB Color Gamut and Gamma values through the color management system (CMS). Color features are pre-set for 255 monotonic gray levels. EMULATION DVI-I(A) DVI-I(D) DVI-D PLNR DVI-I(A) DVI-I(D) DVI-D HDMI(Y) HDMI(R) PICTURE BRIGHTNESS CONTRAST GAMMA BLACK LEVEL WHITE BALANCE DVI-I(A) DVI-I(D) DVI-D HDMI(Y) HDMI(R) HDMI(Y) HDMI(R) DVI-I(A) Standard image settings. 18 On Screen Display(OSD) Selection and Adjustment COLOR COLOR TEMP (PRESET) 5000K 6500K 7200K 8200K 9300K DVI-I(A) DVI-I(D) DVI-D HDMI(Y) HDMI(R) Color temperature adjustments (USER) RED GREEN BLUE HUE SATURATION SIX COLOR (RED/GREEN/ BLUE/CYAN/ MAGENTA/ YELLOW) COLOR RESET TRACKING HORIZONTAL VERTICAL CLOCK PHASE SHARPNESS DVI-I(A) Adjusts the position of the screen Adjusts the clarity and stability of the screen DVI-I(A) DVI-I(A) DVI-I(D) DVI-D HDMI(Y) HDMI(R) HORIZONTAL MIRRORING DVI-I(A) DVI-I(D) DVI-D HDMI(Y) HDMI(R) To adjust to set the image mirroring(horizontal inversion). SETUP LANGUAGE OSD POSITION (HORIZONTAL / VERTICAL) DVI-I(A) DVI-I(D) DVI-D HDMI(Y) HDMI(R) HDMI(Y) HDMI(R) Additional settings OVERSCAN ARC RTC POWER INDICATOR FACTORY RESET DVI-I(A) DVI-I(D) DVI-D HDMI(Y) HDMI(R) NOTE The order of icons may differ depending on the model (18 to 27). 19 On Screen Display(OSD) Selection and Adjustment The OSD screen will appear when you press the MODE button on the front of the monitor. DVI Input HDMI(RGB) Input HDMI(YUV) Input *When HDMI(RGB) is inputted, CUSTOM, sRGB, ADOBE RGB and PLNR mode are supported. MENU : Exit : Move AUTO/SET : Select Main menu CUSTOM Description The default mode that adjusts the overall range of colors of the RGB LED panel. * In modes other than CUSTOM mode, you cannot adjust the PICTRUE (CONTRAST, GAMMA) and COLOR functions of the main menu. sRGB Color features are set for sRGB specification. Color Temperature, Brightness, Gamma and x and y coordinates of RGBCMY are adjusted based on the sRGB specification. 20 On Screen Display(OSD) Selection and Adjustment Main menu ADOBE RGB Description Color features are set for Adobe RGB specification. [. . . ] · Check if the signal cable is properly connected and use a screwdriver to fasten if necessary. · Set the color setting higher than 24 bits (true color) at Control Panel - Settings. · Check if the screen is set to interlace mode and if yes, change it to the recommend resolution. G The screen blinks. Do you see an "Unrecognized monitor, Plug&Play (VESA DDC) monitor found" message? G Have you installed the display driver?· Be sure to install the display driver from the display driver CD (or diskette) that comes with your display. [. . . ]