User manual PLANAR PX2320MW Product Manual

[. . . ] 5 Start Your Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 User Controls Front Panel Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 How to Use the OSD Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 On-Screen Display Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The VESA Mounting slots of this model are located inside the rear cover (shown in the following figure). To mount the monitor on a swing arm or other mounting fixture, follow the instruction included with the mounting fixture to be used. Slots 100mm 100mm VESA Mounting Interface Warning!The depth from plastic back cover to the bottom of the screw hole is 8mm. The spec is M4 screw. 8 Start Your Installation u Connecting the Display (Figure 10. 1) To setup this display, please refer to the following figure and procedures. Connect the DC power cord to the power connector; plug one end of the AC power cord into the power adapter, and the other end into an electrical outlet(). For the PC with Analog output: Connect the VGA signal cable from display VGA input connector to the 15-pin connector of your host computer and tighten the screws(). For the PC with DVI digital output: Connect the DVI signal cable to the connector of the display card in your computer; connect the other side to the DVI-D input port of your display. If your video source uses a round, four-prong S-Video connector, please use the S-Video cable(). If your video source uses a round, one-prong composite video connector, please use the video cable(). If your audio source uses a round, one-prong composite audio connector, please use the audio cable(). Turn on your computer, display and video source. Notice:To ensure the LCD Display will work well with your computer, please configure the display mode of your graphics card to make it less than or equal to 1920 x 1200 resolution and make sure the timing of the display mode is compatible with the LCD screen. We have listed the "Compatibility Modes" of this LCD screen in appendices for your reference. 9 Figure 10. 1 10 User Controls Front Panel Controls No/Icon MENU Control Menu button 1. 1. To activate the"Auto Adjustment" 0 function to obtain an optimum image. Adjust Power LED Power switch 11 How to Use the OSD Menus 1. Press the "MENU" button to pop up the on-screen menu and to select among the six Main Menus. 2. Choose the adjustment items by pressing the "SELECT" button. Adjust the value of the adjustment items by pressing the " or " " button. 4. After a period of inactivity the OSD menus will automatically disappear. 4 3 " 12 On-Screen Display Menus Main Menu Menu Level 2 Volume Contrast Color PIP Mode PIP Source Size H. Position Source Aspect Ratio Menu Level 3 Function Description To adjust the sound volume. Allows you to select Video, and S-Video Allows you to adjust size of display. Changes the displays data frequency to match the frequency of your graphics card. [. . . ] To adjust the amount of time the OSD menu is to remain displayed. OSD H. Position Information Reset Allows you to move the horizontal position of the OSD window. To return the display parameters of the current mode to their fatory default settings. 14 Appendix Troubleshooting If you are experiencing trouble with the LCD display, refer to the following trouble shooting. If the problem persists, please contact your local dealer or our service center. [. . . ]