User manual PLANAR PT1704N Product Manual

[. . . ] Consult the dealer or an experienced radio/TV technician for help. Caution: To comply with the limits for an FCC Class B computing device, always use the shielded signal cord supplied with this unit. The Federal Communications Commission warns that changes or modifications of the unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. CE mark for Class B ITE (Following European standard EN55022/1998; EN61000-3-2/1995; EN61000-3-3/1995, EN55024/1998) Radio Frequency Interference Statement Warning: This is a Class B product. In a domestic environment, this product may cause radio interference in which case the user may be required to take adequate measures. Canadian Doc Notice For Class B Computing Devices i Planar User's Manual This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the Radio Interference Regulation of the Canadian Department of Communications. "Le présent appareil numérique n'èmet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la class B prescrites dans le Règlement sur le brouillage radioélectrique édicté par le ministère des Communications du Canada" Important Safety Instructions Please read the following instructions carefully. [. . . ] The screen is capable of supporting a maximum resolution of 1280 x 1024 (SXGA). Function Select Buttons These two buttons allow you to select the control functions in the OSD. Press either button to vertically scroll through the main menu and submenu items. Adjust Control Buttons This button allows you to apply settings and enter submenus in the OSD. Power ON / OFF and Menu Button This button allows you to activate the OSD Menu. Press the button and hold it down for two seconds will turn on or turn off the monitor. Power-On Indicator This LED indicator stays lit when the power is on and when the monitor is receiving a proper video signal. The LED will blink slowly when the LCD monitor is in power saving mode. Using the OSD, you can adjust the contrast, brightness, display position, display clarity, and color temperature. Please read this chapter carefully to get the most out of your New Planar LCD Monitor. Adjusting the Monitor's Display The LCD monitor features an intuitive, menu-driven, On-Screen Display (OSD). If the PC is in a power saving mode, or is powered down, the OSD is inaccessible. OSD Main Menu To activate the OSD Main Menu, press the topmost Function key. To navigate the topline menu, use the down arrow key to scroll between the main menu choices. Each main menu has an associated submenu and is further described. OSD Main Menu To access the OSD Main Menu, simply press the Function button. Main menu Submenu Description The 7-topline menus are: The Auto Adjust option lets the monitor determine and select the settings that are most appropriate for your system requirements. This function will tune the display to your computers video card. The Monitor-Control option allows you to adjust the LCD monitor's display characteristics such as the display's horizontal or vertical position, display phase, display clock, and factory reset. Adjusting these settings should only be necessary if the results from Auto-Adjust function are not satisfactory. 5 Planar User's Manual The OSD-Control option allows you to adjust the position and setting of the monitor's On Screen Display. The MISC-Control option allows you to select the desired text language of the OSD, adjust the monitor speaker volume, and to display the current video information being sent to the monitor from your video card. The Graphic-Control option allows you to adjust the display contrast, brightness, sharpness, and color settings. The Graph/Tex option allows you to switch DOS text resolution from 640x400 and 720x400. This function has no effect within graphic operating systems such as MS WindowsTM. The OSD Exit option closes the On Screen Display. Auto Adjust Procedure Pressing the Adjust key while the Auto Adjust topline menu is selected, activates the Auto Adjust procedure. Once finished, the OSD menu will disappear after a short time-out period. The Monitor- Control Option Pressing the Adjust key while the Monitor Control icon is selected activates the Monitor Control submenu. You should only use this menu item if the results of the Auto Adjust function are not satisfactory. H-Position: Press the V-Position: Press the Adjust Adjust buttons to horizontally move the display image to the desired position. buttons to vertically move the display image to the desired position. Phase: Press the Adjust buttons to fine-tune the displayed image. An improper phase adjustment will result in pixel jitter or display noise. [. . . ] Press the upper Function Control button (refer to Chapter 2) once and then press either the upper or lower Adjustment Control button several times. If there is still no display, press the other Adjustment Control button several times. If step 2 doesn't work, connect your PC system to another external CRT. If your PC System functions properly with a CRT Monitor but it does not function with your New Planar LCD Monitor, and your New Planar LCD Monitor's power LED is blinking, the output timing of the PC's VGA card may be out of the LCD's synchronous range. [. . . ]