User manual PLANAR PT1520MU Product Manual

[. . . ] 12 How to Use the OSD Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 On-Screen Display Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Appendices Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Warning Signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The Kensington lock is not included. Kensington Security Slot VESA Mount This monitor conforms to the VESA Flat Panel Mounting Physical Mounting Interface Standard which defines a physical mounting interface for flat panel monitors, and corresponding standards for flat panel monitor mounting devices, such as wall and table arms. The 75 mm VESA hole pattern is located inside the rear cover (shown in the following figure). To mount the monitor on a swing arm or other mounting fixture, follow the instruction included with the mounting fixture to be used. 75mm 8 Slots 75mm VESA Mounting Interface Removing the Deskstand 1. Push clips down ( ) and pull the VESA cover from the rear of the display by the ears ( ). You my need a screw driver or some other item to help you dislodge and prop the first clip while you dislodge the second clip. Unscrew the 4 screws from the rear cover using a Philips screw driver. The correct screw type to use is M4 x 12. Cable Management . 9 1. Pull all the cables forward while the tilt angle is 90°. 10 Start Your Installation Connecting the Display (Figure 10. 1) To setup this display, please refer to the following figure and procedures. Connect the DC power cord to the power connector; plug one end of the AC power cord into the power adapter, and the other end into an electrical outlet ( ). Connect the VGA signal cable from display VGA input connector to the 15-pin connector of your host computer and tighten the screws ( ). Connect the Audio-In cable from audio input port of your display to the Audio-out port of your computer ( ). Connect the USB cable from USB port of your display to the USB port of your computer( ). Refer to the "Touch Screen Driver Installation" section on page 19. Once the touch screen is configured, turn on your computer, display and video source. Notice: To ensure the LCD Display will work well with your computer, please configure the display mode of your graphics card to make it less than or equal to 1024 x 768 resolution and make sure the timing of the display mode is compatible with the LCD screen. We have listed the "Compatibility Modes" of this LCD screen in appendices for your reference. 11 Figure 10. 1 Power Cord VGA Cable Audio-In Cable USB Cable 12 User Controls Front Panel Controls No / Icon Control Power Switch Function on/ off the power of the LCD display. Auto - To activate the "Auto Adjustment" function to obtain an optimum image. Display the OSD menus. Power LED S M Select/Auto Plus/Brightness Minus/Mute On/Off Menu Button 13 How to Use the OSD Menus 1. Press the "MENU" button to pop up the "on-screen menu" and to select among the four Main Menus. Choose the adjustment items by pressing the "Select/Auto" button. Adjust the value of the adjustment items by pressing the "+"or "-" button. The OSD menu will automatically close if you have left it idle for a pre-set amount of time. To disable the OSD menu buttons, please follow the instructions below. [. . . ] Opens the Language sub-menu where you can select Default is English the desired language of the OSD. Default is 100 Default is 100 Default is 100 Default is 20 Default is 70 Remark 15 Appendix Troubleshooting If you are experiencing trouble with the LCD display, refer to the following. Problem: No image appears on screen. Check that all the I/O and power connectors are correctly installed and well connected as described in the "Installation" section. Reconfigure the resolution of your computer to make it less than or equal to 1024 x 768. Problem: Partial Image or incorrectly displayed the image. Check to see if the resolution of your computer is higher than that of the LCD display. [. . . ]