User manual PLANAR PT120 Product Manual

[. . . ] Connect the equipment into an outlet different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Caution: To comply with the limits for an FCC Class B computing device, always use the shielded signal cord supplied with this unit. The Federal Communications Commission warns that changes or modifications of the unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. CE mark for Class B ITE (Following European standard EN55022/1998; EN610003-2/1995; EN61000-3-3/1995, EN55024/1998, EN60950/1992+A1+A2+A3+A4+A11) Radio Frequency Interference Statement Warning: This is a Class B product. [. . . ] You can use the LCD Monitor for everything from making business presentations to playing computer games. The architecture of the LCD Monitor incorporates an LCD panel that produces a clear display with low radiation emission, limiting health concerns. With its low power consumption, the LCD Monitor helps you reduce your power bill. Unpacking Before you unpack your LCD Monitor, prepare a suitable workspace for your LCD Monitor and computer. Even though the LCD Monitor uses very little power, you should put it in a location which allows sufficient airflow to ensure that the LCD Monitor and your computer does not become too hot. Set up your LCD Monitor so that the panel doesn't face a window where sunlight often comes in. The glare caused by sunlight reflecting off the LCD Monitor's screen will makes it difficult to see. After you unpack your LCD Monitor; make sure the following items are included in the box and in good condition: · · LCD Monitor Monitor-to-PC signal cable 1 User's Manual · · · AC Adapter Power cord This user's manual If you find that any of these items are missing or appear damaged, contact your dealer immediately. Do not throw away the packing material or shipping carton in case you need to ship or store the LCD Monitor in the future. Identifying Components The LCD Monitor has been designed to provide easy access to all controls and peripheral ports. The following figures will help you identify the LCD Monitor's controls and ports. The LCD Monitor -- Front View Figure 1-1: The LCD Monitor Panel and Controls 1. LCD Screen The LCD Monitor Screen is capable of producing most display standards. Function Control Buttons The 1st button allows you to pop up the OSD Menu and to 2 Chapter 1 select the function group. The 2nd button allows you to select one of the control functions within each function group. Adjustment Control Buttons These two buttons allow you to adjust the selected control function to accommodate your specific working environment. Press the upper button to increase the setting of the selected control function and press the lower button to decrease the setting of the selected control function. The LED indicator will blink when the LCD Monitor is in Power Saving mode. Monitor Stand The Monitor Stand supports the LCD Panel. 3 User's Manual The LCD Monitor -- Rear View Figure 1-2: LCD Monitor's Rear Ports 1. LCD Monitor's VGA Connector This 1. 5 meter cable has two 15-pin D-Sub VGA connectors used to connect the monitor to your PC's VGA card. RS232 Connector for Optional Touch Screen Connect this RS232 connector to your PC's RS232 9-pin serial port connector to use the Optional Touch Screen. To install the Optional Touch Screen driver, please contact your local distributor. 4 Chapter 1 Adjusting the Viewing Angle Your LCD Monitor is designed to allow you to adjust it to a comfortable viewing angle. The LCD Monitor's angle setting range is from -5° to 25°. Please see Figure 1-3. Figure 1-3: Angle Settings · · · When positioning the equipment, make sure that the main ports and sockets are easily accessible. Moisture and direct sunlight exposure can be seriously damaging. 5 User's Manual Connecting AC Power Please refer to the following instructions for connecting AC power to the LCD Monitor. [. . . ] Press the upper Function Control button (refer to Chapter 2) once and then press either the upper or lower Adjustment Control button several times. If there is still no display, press the other Adjustment Control button several times. If step 2 doesn't work, connect your PC system to another external CRT. If your PC System functions properly with a CRT Monitor but it does not function with the LCD Monitor, and the LCD Monitor's power LED is blinking, the output timing of the PC's VGA card may be out of the LCD's synchronous range. [. . . ]