User manual PLANAR PL1911M Product Manual

[. . . ] 5 Interface for Arm Applications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Connecting the Display to your Computer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Connecting the AC Power. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Connecting the Audio Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] A certified line is required to connect this device to a power outlet. For a nominal current up to 6A and a device weight above 3 kg, a line not lighter than H05VV-F, 3G, 0. 75 mm2 must be used. Important Recycle Instruction: LCD Lamp(s) inside this product contain mercury. This product may contain other electronic waste that can be hazardous if not disposed of properly. For more information, contact the Electronic Industries Alliance at WWW. EIAE. ORG. For lamp specific disposal information check WWW. LAMPRECYCLE. ORG. 3 Chapter 1 Installation Unpacking Before unpacking the LCD Monitor, prepare a suitable workspace for your Monitor and computer. Make sure that LCD Monitor has enough space around it for sufficient airflow. Though the LCD Monitor uses very little power, some ventilation is needed to ensure that the Monitor does not become too hot. After you unpack the LCD Monitor, make sure that the following items were included in the box: * LCD Monitor * Monitor-to-PC VGA Cable * Monitor-to-PC DVI-D Cable * User's Manual * Power Cord * Stereo Jack Audio Cable Register Your Planar Products Today Thank you for choosing Planar. To assure you receive all the benefits of your Planar product and services, register your Planar product today. Visit our website to register your product at http://www. planar. com/support/product_registration. html Cables, Replacement Lamps and Accessories To find cables, replacement lamps and accessories for your Planar projector, LCD monitor, touchscreen or other Planar products visit our online store at www. PlanarOnline. com or find other stores who carry Planar products at http://www. planar. com/howtobuy 4 Height Adjustment Stand To unlock the height adjustment feature of the stand, locate the pin on the back of the stand column and turn the pin knob counter-clockwise. (See fig. 1-1 ) Figure 1-1 Tilt, Swivel and Pivot Rotation The LCD Monitor is designed to have a tilt range of -5°to +25°, a swivel range of -35°to +35°, and a 90° pivot rotation. 1-2) Figure 1-2 Warning: Do not force the LCD Monitor over its maximum viewing angle settings as stated above. Attempting this will result in damaging the Monitor and Monitor stand. Raise the monitor to its "Full Up" position before removing the monitor stand. Optional Mounting Alternatives Warning: The monitor stand base may forcefully extend and cause injury. Raise the monitor to its "Full Up" Optional Mounting Alternatives Warning: The monitor stand base may forcefully extend and cause injury. Raise the monitor to its "Full Up" position before removing the monitor stand. Detaching LCD Monitor from Its Stand Unscrew screws the swivel base support column and pull down the second. Figure 1-3 Interface for Arm Applications Before installing to mounting device, please refer to Fig. 1-3. The rear of this LCD display has four integrated 4 mm, 0. 7 pitches threaded nuts, as well as four 5 mm access holes in the plastic covering as illustrated in Figure 1-4. These specifications meet the VESA Flat Panel Monitor Physical Mounting Interface Standard (paragraphs 2. 1 and 2. 1. 3, version 1, dated 13 November 1997). Note :Please using Ø 4mm x 8mm (L) screw for this application. Figure 1-4 5 Connecting the Display to your Computer 1. Connect one end of the signal cable to the LCD Monitor's VGA port or DVI port. (See Fig 1-5) 3. Connect the other end of the signal cable to the VGA port or DVI port on your PC. Make sure connections are secure. Figure 1-5 Connecting the AC Power 1. [. . . ] Move to "Phase" function in OSD menu again and adjust the monitor screen to its most clear display. Click "No" on "Shut Down Windows" and back to the normal PC operating environment. PROBLEM There is no picture on LCD Monitor If there's no picture on the LCD Monitor, please perform the following steps: 1. Make sure the power indicator on the LCD Monitor is ON, all connections are secured, and the system is running on the correct timing. If there is still no picture, press the Adjustment Control button several times. [. . . ]