User manual PLANAR PL1910W

[. . . ] This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instruction, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · · · · Reposition or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. [. . . ] For displays with glossy bezels the user should consider the placement of the display as the bezel may cause disturbing reflections from surrounding light and bright surfaces. Cleaning Your Monitor Please carefully follow the guidelines below when cleaning the monitor. Use a soft cloth to wipe the screen and cabinet front and sides. About Power Cable Check first to make sure that the power cord you use is the correct type required for your area. This monitor has a universal power supply that allows operation in either 100/120V AC or 220/240 V AC voltage area. Plug one end of the power cord to the AC Inlet, plug another end to a proper AC outlet. For unit using at 120 V AC: Use a UL Listed Cord Set, Type SVT wire and plug rated 10 A/125 V. For unit using at 220/240 V AC (outside of U. S. ): Use a Cord Set consisting of H05VV-F cord and plug rated 10 A, 250 V. The cord set should have the appropriate safety approvals for the country In which the equipment will be installed. 3 Installation Introduction Congratulations on your purchase of PL1910W, a high performance 18. 5 inch wide color TFT LCD monitor. Features * 18. 5" TFT Color LCD monitor * 16:9 Widescreen * Recommended resolution: 1366 x 768 @ 60Hz * Direct analog signal input * Direct digital signal input * Auto adjustment function * Multilingual OSD user control * Kensington security slot * 100mm VESA mount * Compact, space saving, sleek cabinet design. 4 Unpacking Please check that the following items are present when you unpack the box. We recommend you save the packaging for future use. PJ19W User Guide AC Power Cord LCD Monitor 15-pin D-Sub Cable DVI Cable 5 Attaching the Base: 1. Lay the TFT LCD monitor on a flat surface with the LCD screen face down. To prevent the monitor from being scratched, put a soft cloth on the table. 2. Unpack the base and attach to stand as shown. 6 Removing the Base 1. Lay the TFT LCD monitor on a flat surface with the LCD screen face down. To prevent the monitor from being scratched, put a soft cloth on the table. Press the release button on the base while pulling away from the stand. 3. Press the release button on the stand while pulling away from the monitor. 7 Preparing The Monitor For Wall-Mounting 1. The rear of this LCD display has 4 integrated 4 mm, 0. 7 pitches threaded nuts. Use the four holes (A), (B), (C), and (D) to attach the swing arm or other mounting fixture to the back of the monitor with screws (not supplied). Follow the instructions included with the mounting fixture to ensure that the monitor is safely attached. The four threaded holes that are on the back of the panel are compliant with the VESA standard for mounting flat-panel monitors. Attach a swing arm or other mounting fixture. 8 Screen Position Adjustment In order to optimize the best viewing position, you can adjust the tilt of the monitor as shown in the figure below. 9 Connecting Cables To install the monitor to your host system, please follow the steps as given below: DVI VGA 1-1 VGA 1-2 DVI 2 Steps 2 1-2 1-1 1. Connect power cord Connect the power cord to the monitor, then to a properly grounded AC outlet. [. . . ] LED displays amber color Check if video signal cable is properly connected to the monitor. Abnormal Picture Unstable Picture Display is missing, center shift, or too small or too large in display size Check if the specification of graphics adapter and Using OSD, adjust RESOLUTION, CLOCK, CLOCKPHASE, H-POSITION and V-POSITION with nonstandard signals. Using OSD, in case of missing full-screen image, please select other resolution or other vertical refresh timing. Wait for a few seconds after adjusting the size of the image before changing or disconnecting the signal cable or powering OFF the monitor. (DVI Mode) Problems No Picture Current Status LED ON LED OFF Remedy Using OSD, adjust brightness and contrast to maximum or reset to their default settings. [. . . ]