User manual PLANAR PL1900

[. . . ] This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. [. . . ] · You may find slightly uneven brightness on the screen depending on the desktop pattern you use. It may include blemishes of 0. 01% or less such as a missing pixel or a pixel lit all of the time. · Due to the nature of the LCD screen, an afterimage of the previous screen may remain after switching the image, when the same image is displayed for hours. In this case, the screen is recovered slowly by changing the image or turning off the Power Switch for hours. 7 BEFORE YOU OPERATE THE MONITOR FEATURES · · · · · 48. 0cm(19") TFT Color LCD Monitor Crisp, Clear Display for Windows Recommended Resolutions: 1280 X 1024 @60Hz EPA ENERGY STAR® Space Saving, Compact Case Design CHECKING THE CONTENTS OF THE PACKAGE The product package should include the following items: Monitor Base Landing Strip User Manual Power Cord 15-pin D-Sub Cable Adapter Register Your Planar Products Today Thank you for choosing Planar. To assure you receive all the benefits of your Planar product and services, register your Planar product today. Visit our website to register your product at http://www. planar. com/support/product_registration. html Cables, Replacement Lamps and Accessories To find cables, replacement lamps and accessories for your Planar projector, LCD monitor, touchscreen or other Planar products visit our online store at www. PlanarOnline. com or find other stores who carry Planar products at http://www. planar. com/howtobuy 8 Installation Instructions Power Source: 1. Make sure that the power cord is the correct type required in your area. This LCD monitor has an External universal power supply that allows operation in either 100/120V AC or 220/240V AC voltage area (No user adjustment is required. ) 3. Connect the AC-power cord into your LCD monitor's External Adapter input socket, and then plug the other end of External adapter to LCD monitor's DC-power-input. The AC-power cord may be connected to either a wall power outlet or the power outlet socket on your PC, depending on the type of power cord supplied with your LCD monitor. 9 Installation Instructions CABLE CONNECTIONS Connecting the Signal Cable: the LCD monitor comes with a built-in signal cable. Plug the signal cables 15-pin connector into the computer's VGA port and tighten the two screws on the cable connector. Connecting the Power Cord: Plug the AC-power cord into the External Adapter. Then plug the DC-jack power cable into DC-IN Inlet. Caution: If the AC outlet is not grounded (with three holes), install the proper grounding adapter (not supplied). Figure 1 1. Signal Cable DC-Jack Power Cable AC Power Cord 10 Installation Instructions ADJUSTING THE VIEWING ANGLE · For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor's angle to your own preference. · Hold the stand so you do not topple the monitor when you change the monitor's angle. · You are able to adjust the monitor's angle from -5° to 20°. Figure 2 NOTES · Do not touch the LCD screen when you change the angle. · Careful attention is required not to catch your fingers or hands when you change the angle. 11 OPERATING INSTRUCTIONS GENERAL INSTRUCTIONS Press the power button to turn the monitor on or off. The other control buttons are located at front panel of the monitor (See Figure 3). By changing these settings, the picture can be adjusted to your personal preferences. Auto Adjust Key/Exit 12 OPERATING INSTRUCTIONS(cont. ) · Power Button: Press this button to switch ON/OFF of monitor's power. · MENU / ENTER : Active OSD menu or function adjust confirm or Exit OSD menu when in Brightness/Contrast OSD status. When OSD menu is in active status, this button will act as EXIT-KEY (EXIT OSD menu). When OSD menu is in off status, press this button over 2 seconds to activate the Auto Adjustment function. [. . . ] With a wrong phase adjustment the picture has horizontal disturbances in light picture. For FOCUS and CLOCK adjustment use "dot-pattern" or win 95/98 shut-down mode pattern. ERROR MESSAGE & POSSIBLE SOLUTION CABLE NOT CONNECTED : 1. Check the signal-cable's connection pins for damage. INPUT NOT SUPPORT : Your computer has been set to unsuitable display mode, set the computer to display mode given in the following table. (see page 22) 19 APPENDIX SPECIFICATIONS Driving system Size Pixel pitch Video Separate Sync. H-Frequency V-Frequency TFT Color LCD 48. 0cm(19") 0. 294mm( H ) × 0. 294mm( V ) R, G, B Analog Interface H/V TTL 30kHz ­ 83kHz (Analog) 55-75Hz (Analog) 16. 2M Colors 135MHz (Analog) 1280 × 1024 @75Hz(Analog) VESA DDC2BTM 37W 2W 15-pin D-Sub Analog:0. 7Vp-p(standard), 75 OHM, Positive Horizontal : 376. 32mm Vertical : 301. 056mm 100~240VAC, 47~63Hz Operating Temp: 5° to 50°C Storage Temp. : -20° to 60°C Operating Humidity : 10% to 85% 406×404×207 (W ×H×D)mm 4. 1kg Unit (net) LCD Panel Input Display Colors Dot Clock Max. [. . . ]