User manual PLANAR PL170 Product Manual

[. . . ] A proper type of power cord has been selected according to the safety of destination and must be used to prevent electric shock. PL170 1 Contents Note: To access our Users Guide Homepage (Page 2) at anytime, simply click on the below Homepage icon or use the arrow icon(s) to browse through each page. When in Homepage, clicking on your desired topic will automatically open each page. Important Safety Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] If it is still not clean, blow and wipe gently with a soft, clean, lint-free cloth. Do not apply pressure to the LCD panel. 4 Adjusting the Monitor Press down on the stand and gently adjust the monitor to a suitable viewing angle (see Figure below). Please note that this monitor can only be tilted forward to 5 degree and backward to 20 degrees. To prevent damage to the monitor, do not press the screen over its tolerant angles. 5 O 20 O 5 Quick Installation Make sure the computer is turned off. Attach the female end of the power cord (Indication F) to the adapter (Indication E), then plug the adapter connector to the power "DC-IN (Indication A)" jack of the LCD monitor. Plug one end of the 15pin D-Sub signal cable (Indication D) in the "ANALOG" video signal connector (Indication C) of LCD monitor. Before your operations of the monitor, please refer to P. 7 "Operations" first. A C D E F A. Power Cord 6 Operations Push the power button (Indication E) on the front of the LCD monitor to turn it on. When the power light (Indication F) turns green, the LCD is ready to use. Power LED B C D E F Press this button to turn on/off the OSD (On Screen Display) main menu. To increase the value of selected item. Press this button to activate "AUTO SYNC", "AUTO-CONTRAST" and "BRIGHTNESS". When the light is green, the power is on and orange is when the power is active off. Hot Keys Auto: Press the [Auto] button to activate Auto-Sync, Auto-Contrast and Brightness under any circumstances. 7 OSD Main Menu For screen adjustments, press the [Menu] button to display the OSD (On-Screen Display) Main Menu shown below. Press the [+] or [-] button to scroll up or down the menu to your required options. Please note that the OSD will automatically turn off in 30 seconds without any manipulation or by simply pressing the [Menu] button for 2 seconds. CONTRAST Adjusts the contrast level of the screen image. Under Main Menu, select CONTRAST using the [+] or [-] button, then press [Menu] button to activate the function. Press the [+] button to increase contrast, [-] button to decrease contrast shown below. Press [Menu] to return to Main Menu. AUTO­CONTRAST Automatically adjusts contrast level of screen image. Press [+] or [-] button to select AUTO CONTRAST, then press [Menu] button to activate AUTO CONTRAST. AUTO­SYNC Automatically adjusts the image to the best performance. Press [+] or [-] button to select AUTO SYNC, then press [Menu] button to activate AUTO SYNC. NOTE: When setting up this monitor for the first time, perform AUTO-SYNC before use. To perform AUTO-SYNC, first display an image that makes the entire screen very bright. It is better to perform AUTO-SYNC under WINDOWS. BRIGHTNESS Adjusts the brightness level of screen image. [. . . ] This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. [. . . ]