User manual PLANAR PE150 Product Manual

[. . . ] 4 Adjusting the Monitor's Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Function Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Chapter 3 Technical Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Standard Timing Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] * Liquid spilled into LCD Monitor or the monitor has been exposed to rain. A certified line is required to connect this device to a power outlet. For a nominal current up to 6A and a device weight above 3 kg, a line not lighter than H05VV-F, 3G, 0. 75 mm2 must be used. Chapter 1 Installation Unpacking Before unpacking the LCD Monitor, prepare a suitable workspace for your Monitor and computer. Make sure that LCD Monitor has enough space around it for sufficient airflow. Though the LCD Monitor uses very little power, some ventilation is needed to ensure that the Monitor does not become too hot. After you unpack the LCD Monitor, make sure that the following items were included in the box: * LCD Monitor * User's Manual * 1. 5M Monitor-to-PC signal Cable * 1. 8M Power Cord * Base If you find that any of these items is missing or appears damaged, contact your dealer immediately. Connecting the LCD Monitor and Base When you open the box to take the base and put on the desk first. Then connect the LCD Monitor and base please. (See fig. 1-1 ) Figure 1-1 Viewing Angle Adjustment The LCD Monitor is designed to allow users to have a comfortable viewing angle. 1-2) Figure 1-2 Warning Do not force the LCD Monitor over its maximum viewing angle settings as stated above. Attempting this will result in damaging the Monitor and Monitor stand. 2 Detaching LCD Monitor from Its Stand 1. 1-3) Figure 1-3 Interface for Arm Applications Before installing to mounting device, please refer to Fig. 1-3. The rear of this LCD display has four integrated 4 mm, 0. 7 pitches threaded nuts, as well as four 5 mm access holes in the plastic covering as illustrated in Figure 1-4. These specifications meet the VESA Flat Panel Monitor Physical Mounting Interface Standard (paragraphs 2. 1 and 2. 1. 3, version 1, dated 13 November 1997). Make sure connection are secure. Figure 1-5 Attention This device must be connected to an off-the-shelf video cable in order to comply with FCC regulations. A ferrite-core interface cable is included in the LCD Monitor package. This device will not be in compliance with FCC regulations when a non-ferrite-core video cable is used. Connecting the AC Power 1. Connect the plug Pin of power cord to an AC power source. Figure 1-6 Setting Up the LCD Monitor 1. Turn on the LCD Monitor's power switch, located on the bezel of the monitor. 3 Power Management System This LCD Monitor complies with the VESA DPMS (version 1. 0) Power Management guidelines. The VESA DPMS provides four power saving modes through detecting a horizontal or vertical sync. When the LCD Monitor is in power saving mode, the monitor screen will be blank and the power LED indicator will light yellow. Chapter 2 Display Controls User Controls A brief description and the location of all LCD Monitor function controls and indicators: Figure 2-1 1 2 3 4 DC Power Switch DC Power-On Indicator Function Select Buttons Adjustment Control Buttons Press the power switch to switch the monitor ON/OFF. Press either left or right control button for OSD (On Screen Display) menu selection. Press the left button to decrease the OSD setting and press the right button to increase the OSD setting. Adjusting the Monitor's Display The monitor has four function control buttons to select among functions shown on OSD menu, designed for easy user-viewing environments. OSD Function Menu To access OSD Main menu, simply press one of the Function Select control buttons, and the menu diagram will pop up on the screen as shown on Fig. 2-2: Continue pressing the Function Select buttons to scroll through the entire menu items , then press Adjustment Control buttons to adjust content of selected item. Figure 2-2 Attention Firmware revision may have been updated into a latest version while the version number shown on all OSD menus in this manual will stay as Ver. [. . . ] Click "No" on "Shut Down Windows" and back to the normal PC operating environment. PROBLEM There is no picture on LCD Monitor If there's no picture on the LCD Monitor, please perform the following steps: 1. Make sure the power indicator on the LCD Monitor is ON, all connections are secured, and the system is running on the correct timing. If there is still no picture, press the Adjustment Control button several times. [. . . ]