User manual PLANAR PDP60B PRODUCT MANUAL
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual PLANAR PDP60B. We hope that this PLANAR PDP60B user guide will be useful to you.
Manual abstract: user guide PLANAR PDP60BPRODUCT MANUAL
Detailed instructions for use are in the User's Guide.
[. . . ] Manual
PLANAR 60B PDP
Safety Precautions
Power Supply - Warning
AC plug should not be touched with wet hands. It may cause an electrical shock.
°§It can cause an electrical shock.
Do not use damaged electrical cord/plug, or loose outlet.
°§It can cause an electric shock or a fire.
Do not use multiple devices in an outlet at the same time to avoid the overload.
°§ may cause a fire due to over heating It
from the outlet.
Power Supply - Warning
Fully insert the plug into the outlet
°§If the connection is unstable, it
may cause a fire.
Be careful not to forcibly bend the electrical cords or press them with a heavy object.
°§It may cause an electrical shock or a
fire.
Be sure to ground the PDP power source.
°§It may cause an electrical shock if it has
a failure or electrical leakage. Only use the proper power cord supplied with PDP and connect it to an outlet with a ground terminal.
Power Supply - Caution
Wh en un plug ging the AC cord, pull out by holding the plug itself and not by pulling on the cord.
°§If the power cord is damaged. it
may cause a fire.
This manual describes how to operate the PDP properly and safely. [. . . ] When setting the monitor, select standard monitor type and then use it. You can set PC output mode to VGA (640 X 480)/ SVGA (800 X 600)/ XGA (1024 X 768). In the mode more than SXGA (1280 X 1024), "Out of Range" message appears. When connecting to PDP monitor, be sure to change into less than XGA mode. Please refer to page 52 for the modes that PDP supports. ).
Turning on PDP monitor °§Selecting input signal
Before turning on the PDP monitor
Insert the power plug. Please use only after carefully reading this manual.
Turning on the PDP monitor
First check the power connection and check the connection of external equipment.
Power On/Off
How to turn on PDP monitor - Press the "Main Power Button (A/C input button)" of monitor and then press the Sub-power button. Turn on/off by remote control - Press the power button of remote control (If the monitor is not turned on, check if the "Main Power Button" on the monitor's main body is pressed first. If the "Main Power Button" is pressed, the power indication lamp will be turned on. ) Turning off PDP monitor - Pres s "Sub-Power Button" on the monitor and then press the "Main Power Button". - You can have the power saving effect (Power Consumption Zero) the same as if you unplugged the power cord.
°ÿ If ON Time settings are made, make sure that you turn off the monitor with "Sub-Power
Button" or remote control.
Selecting External Input.
Select the required input using button and then select with button in the next menu by pressing input selection
(Enter) button.
If you know the input connected on the back of the monitor, you can instantly make the input selection by pressing VIDEO button, S-VIDEO button, COMPONENT button, RGB/A button, and RGB/D button on the remote control. EX) When selecting ANALOG RGB, press RGB/A button on the remote control.
Volume - Controlling Volume°§Mute - Pausing sound °§Still - Pausing the screen°§Info - Checking current state °§Menu - checking the menu
Volume - Controlling Volume
Press button to increase volume, Press button to decrease volume.
Mute - Pausing sound
Press button. If you press the button again, the sound turns back on.
Still - Pausing the screen
Press button. If you press the button again, the screen moves again.
Info - Checking current INFO
Press button. It automati-
cally disappears after three (3) seconds.
Menu - Checking the menu
If input selections are "Composite", "S-Video", and "Component", the video menu is activated. If input selections are "Analog RGB" and, "Digital RGB", the computer menu activates. You should use the remote control for detailed menu item setting and change of PDP monitor.
Press
button.
When you press the
button, the screen appears in turn as shown in the figure.
Use menu.
button to move to sub menu and store the setting value. Use
button to move main
[ Video Mode ]
[ Computer Mode ]
[ Sound Mode ]
[ Equalizer ]
[ Setup Mode ]
[ Timer Mode ]
PSM °§User setting
Adjusting video screen
How to change the screen mood. Press "PSM" button.
Press
PSM"
button repeatedly to select the desired screen.
Standard
Dynamic
Movie
Mild
Game
User
Press
button.
Press
button to move to the item
®ËPress
button to enter the sub-menu.
®È Select "Picture" with
®Í Select the required mode with · Standard: It is the best screen state set in the factory. (Please refer to page 29 on screen adjustment method. )
User setting - manually setting the screen mode
You may change the user setting from any mode.
Press the
button
Press
button move to the item
®Ë Press
button to enter the sub-menu.
®È Select "Brightness" with
.
®Í
Set the value with
.
Press
button to return to previous menu.
User Mode
· Brightness: Adjust the entire screen bright or dark. · Contrast: Adjust the difference of brightness and darkness between the object and the back-
ground.
· Color: Adjust the color to light or dark. · Sharpness: Adjust clearness and ambiguity of the object's outline.
ARC °§PIP
ARC (Aspect Ratio Control)
Press button.
Whenever you press panorama °Ê 4:3.
button, you can select 16:9 °Ê Zoom1 °Ê Zoom2 °Ê
16:9
Zoom 1
Zoom 2
4:3
Panorama
Zoom 1
Zoom 2
Panorama
Screen Size
· 16:9 - Is the screen size that is configured to the general screen. · Zoom 1 - It is the screen size that extended the entire screen. · Panorama - It is the screen that is configured to a wide screen to be natural as a
general screen.
· 4:3 - It is the screen size of video and that is currently broadcast.
PIP (Picture In Picture)
Press the When you press the button. [. . . ] °ÿ To check the "Sleep Timer" after the setting, press button once.
°ÿ If you turn off the power, the setting of "sleep Timer" is deleted. Repeat the setting again.
Trouble Shooting
Take the following steps first and if you still have the same problem, turn off the power and contact an authorized service center.
· Screen related Matters
Problem
The screen does not appear
Action
Is the power plug pulled out?Turn the main power button on and press the power button of the remote control. This problem occurs for a brief time in the process of image elimination processing in order not to show t he noise of screen that can occur when the power is turned on. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE PLANAR PDP60B
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual PLANAR PDP60B will begin.