User manual PLANAR PDP43P Product Manual

[. . . ] PDP-50P AND PDP-43P OPERATING INSTRUCTIONS This unit has been designed for use as a computer display monitor. The optional video card is required if you wish to view other video signals on the monitor. For details consult your local retail dealer. Contents related to system specifications, power requirements, accessories, and other information differ with respect to the country where this unit is purchased. Operating Instructions Thank you very much for purchasing this Planar product. Before using your Plasma Display, please read the "Safety Precautions" and these "Operating Instructions" carefully so you will know how to operate the Plasma Display properly. [. . . ] Once components are connected, follow the following steps to route cables. * As viewed from the rear of the display. 1 2 1 Installation and Connections Organize cables together using the provided speed clamps. Insert 1 into an appropriate hole on the rear of the unit, then snap 2 into the back of 1 to fix the clamp. Please attach carefully. 2 Bunch separated cables together and secure them with the provided bead bands. Note Cables can be routed to the right or left. To attach the speed clamps to the main unit Connect the speed clamps using the 4 holes marked with · below, depending on the situation. Illustration depicts PDP-50P model. To remove speed clamps Using pliers, twist the clamp 90° and pull it outward. In some cases the clamp may have deteriorated over time and may be damaged when removed. 16 En Setting Up the System Setup after Connection After components have been connected to INPUT1 or INPUT2, on-screen setup is necessary. Follow the procedure described below and make settings as they apply to the type of components connected. 6 Press 5/ to select SETTING, then press SET. MAIN MENU PICTURE SCREEN SET UP I N P UT L A B E L POWE R M A NA GEME NT C L AMP P O S I T I O N SETT I NG INPUT1 OPTION : I N P UT 1 : OF F : AU T O : V GA Screen Mode setup Note These settings are required only when using the following input signal refresh rates: 1 31. 5 kHz horizontal / 60 Hz vertical; 2 48. 4 kHz horizontal / 60 Hz vertical; 3 56. 5 kHz horizontal / 70 Hz vertical. No manual setup is necessary for signals with other refresh rates, since adjustments are performed automatically (the SETTING item will not be displayed). SELECT SET ENTER MENU EXIT 7 Press 2/3 to select the display mode. S E T T I N G : V GA 1 Switch MAIN POWER on the connection panel to the on position to turn on the unit's main power. The menu screen appears. MAIN MENU SCREEN : CO NT RA S T 0 : BR I GHT . E NH AN CE 0 RE S E T PICTURE SET UP INPUT1 OPTION SELECT SET SET MENU EXIT 2 1 When the input signal has a refresh rate of 31. 5 kHz (horizontal) and 60 Hz (vertical), pressing 2/3 will cause the display mode to change alternately as follows: PC AUTO WIDE VGA VGA 3 4 PC AUTO WIDE XGA XGA 3 When the input signal has a refresh rate of 56. 5 kHz (horizontal) and 70 Hz (vertical), pressing 2/3 will cause the display mode to change alternately as follows: XGA WIDE XGA SELECT SET ENTER MENU EXIT 5 Press 2/3 to select SET UP. MAIN MENU PICTURE SCREEN SET UP I N P UT L A B E L POWE R M A NA GEME NT C L AMP P O S I T I O N SETT I NG INPUT1 OPTION : I N P UT 1 : OF F : AU T O : V GA If the PC AUTO setting is selected when using the above PC input signals, screen resolution will automatically switch between VGA/WVGA or XGA/WXGA. Note The PC AUTO setting supports automatic signal selection only when using RGB separate Sync inputs. When G ON SYNC or Composite Sync signals are input, selecting PC AUTO will cause the screen resolution to be set to VGA or XGA only. When using a G ON SYNC or Composite SYNC signal for WIDE VGA or WIDE XGA inputs, set the screen display mode manually. 8 SELECT SET When the setup is completed, press MENU to exit the menu screen. ENTER MENU EXIT Note Make this setup for each input (INPUT1 and INPUT2). 17 En Setting Up the System 2 When the input signal has a refresh rate of 48. 4 kHz (horizontal) and 60 Hz (vertical), pressing 2/3 will cause the display mode to change alternately as follows: Français English Setting Up the System English CLAMP POSITION setup Depending on the signal, analog RGB signals may result in the screen image appearing with a whitish or greenish cast. ÷ Normally, leave this setting at AUTO. 4 Press SET to select LOCKED. MAIN MENU PICTURE SCREEN SET UP I N P UT L A B E L POWE R M A NA GEME NT C L A MP P O S I T I O N SETT I NG INPUT1 OPTION : I N P UT 1 : OF F : L O CK E D : V GA Setup of CLAMP POSITION 1 Press MENU to display the menu screen. E NH AN CE RE S E T SCREEN : 0 : 0 : +60 : +60 : +60 : 0 : 0 SET UP INPUT1 OPTION SELECT SET CHANGE MENU EXIT Mode selection will change as follows each time SET is pressed. 3 AUTO LOCKED 2 5 SELECT SET When the setup is completed, press MENU to exit the menu screen. ENTER MENU EXIT Notes ÷ Make this CLAMP POSITION setting for each applicable input (INPUT1 and INPUT2). ÷ When using this setup, be sure to carefully check the signal output of the component that you are using. For details, please refer to the instruction manual supplied with the component you are connecting. 2 Press 2/3 to select SET UP. MAIN MENU PICTURE SCREEN SET UP I N P UT L A B E L POWE R M A NA GEME NT C L AMP P O S I T I O N SETT I NG INPUT1 OPTION : I N P UT 1 : OF F : AU T O : V GA Setting Up the System SELECT SET ENTER MENU EXIT 3 Press 5/ to select CLAMP POSITION. MAIN MENU PICTURE SCREEN SET UP I N P UT L A B E L POWE R M A NA GEME NT C L A MP P O S I T I O N SETT I NG INPUT1 OPTION : I N P UT 1 : OF F : AUTO : V GA SELECT SET CHANGE MENU EXIT 18 En Operations Selecting an Input Source This section explains the basic operation of this unit. Outlined on the following pages is how to turn the main power on and off, put this unit in the operation or standby mode and how to select connected components. Press INPUT on the remote control unit or the main unit to select the input. Input changes each time the main unit's INPUT is pressed as follows. 3 INPUT1 INPUT2 2 Before you begin, make sure you have: · Made connections between this unit and personal computer as described in the section "Installation and Connections" starting on page 10. · Set up the on-screen menu to input signals from components connected to INPUT1 and INPUT2 as described in the section "Setting Up the System" on page 17. If no connections are made to these terminals, on-screen setup is not necessary. · When the menu screen is displayed, changing the signal input will cause the menu screen to turn off. · If the input computer signal is not supported by the display, the following message will be displayed: I NPUT 1 CA U T I O N U N S UP P O R T E D S I G N AL fH: fV: 7 7. 0 H z 1 15 2X 864 FUL L 2, 5 2, 5 3 I NPUT 1 3 CA U T I O N OU T OF R A N G E f H : 7 5. [. . . ] 2 Cleaning cloth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Speed clamps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Bead bands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]