User manual PLANAR LED2210MW

[. . . ] NOTICE: 1The changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 2Shielded interface cables and AC power cord, if any, must be used in order to comply with the emission limits. 3The manufacturer is not responsible for any radio or TV interference caused by unauthorized modification to this equipment. WARNING: To prevent fire or shock hazard, do not expose the monitor to rain or moisture. [. . . ] CABLE CONNECTIONS Connecting the Signal Cable: Plug one end of the signal cable to the LCD monitor and the other end to a computer or a video source. Connecting the Power Cord: Plug the AC power cord one end to LCD monitor's AC-power AC input socket , the other end to Wall outlet. Connecting the Audio Cable: Connect the audio cable between the monitor's audio input and the PC's audio output. Caution: If the AC outlet is not grounded (with three holes), install the proper grounding adapter (not supplied). Figure 1 1. 4 Connecting Cables AC Power Cord DP Cable D-Sub Cable Sub Audio Cable 9 ADJUSTING THE VIEWING ANGLE For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor's angle to your own preference. Hold the stand so you do not topple the monitor when you change the monitor's angle. You are able to adjust the monitor's angle from -5 to 19. Figure 2 NOTES Do not touch the LCD screen when you change the angle. It may cause damage or break the LCD screen. Careful attention is required not to catch your fingers or hands when you change the angle. 10 OPERATING INSTRUCTIONS GENERAL INSTRUCTIONS Press the power button to turn the monitor on or off. The other control buttons are located at front panel of the monitor (See Figure 4). By changing these settings, the picture can be adjusted to your personal preferences. The power cord should be connected. The power indicator will light up. Figure 3 External Control Button EXTERNAL CONTROLS 1. Source/Auto Adjust/EXIT ECO (-) Power Indicator Power Indicator Volume Hotkey(+) MENU/ENTER Power Button 11 FRONT PANEL CONTROL Power Button: Power Indicator : Press this button to switch ON/OFF monitor's power. Blue --- Power On mode. ECO/(-) Activates the ECO control when the OSD is OFF or navigate through adjustment icons when OSD is ON or adjust a function when function is activated. Volume/+: Activates the volume control when the OSD is OFF or navigate through adjustment icons when OSD is ON or adjust a function when function is activated. Source/Auto Adjust/Exit: When the OSD is OFF, pressing Auto/Source button will toggle between sources. Press continuously to select the input source indicated in the message bar. Auto configure hot key :(VGA input only) When the OSD is OFF, press and hold down the button for 2 seconds to auto configure. When OSD menu is ON, this button will act as a Exit Key (Exit OSD menu) OSD Lock Function: To lock the OSD, press and hold the MENU button while the monitor is off and then press power button to turn the monitor on. To un-lock the OSD - press and hold the MENU button while the monitor is off and then press power button to turn the monitor on. NOTES Do not install the monitor in a location near heat sources such as radiators or air ducts, or in a place subject to direct sunlight, or excessive dust or mechanical vibration or shock. Save the original shipping carton and packing materials, as they will come in handy if you ever have to ship your monitor. For maximum protection, repackage your monitor as it was originally packed at the factory. To keep the monitor looking new, periodically clean it with a soft cloth. Stubborn stains may be removed with a cloth lightly dampened with a mild detergent solution. [. . . ] Resolution Plug & Play Power Consumption Input Connector Input Video Signal ON Mode OFF Mode TFT Color LCD 55cm(21. 5") 0. 248mm( H ) × 0. 248mm( V ) R, G, B Analog Interface, Display Port H/V TTL 24kHz ­ 83kHz (Analog) 50-75Hz (Analog) 16. 7M Colors 165MHz (Analog) 1920 × 1080 @60Hz VESA DDC2BTM 40W 1W 15-pin D-Sub , DP Analog:0. 7Vp-p(standard), 75 OHM, Positive Digital: Display port 100~240VAC, 50/60Hz Operating Temp: 0° to 40°C Storage Temp. : -20° to 60°C Operating Humidity : 15% to 90% 505. 6×365. 8×179. 8(W ×H×D)mm 3. 5kg Unit (net) UL, FCC B, CE Power Source Environmental Considerations Dimension Weight (N. W. ) Regulatory Compliance 20 FACTORY PRESET TIMING TABLE STANDARD RESOLUTION HORIZONTAL FREQUENCY PC MODES VERTICAL FREQUENCY 640x480 VGA 640x480 640x480 800x600 800x600 SVGA 800x600 800x600 1024x768 1024x768 XGA 1024x768 1024x768 1280x1024 1280x1024 SXGA 1280x1024 1280x1024 1280x960 WXGA+ WSXGA 1080P 1440x900 1680x1050 1920x1080 31. 469kHz 37. 861kHz 37. 500kHz 35. 156kHz 37. 879kHz 48. 077kHz 46. 875kHz 48. 363kHz 56. 476kHz 57. 700kHz 60. 023kHz 63. 981kHz 74. 40kHz 77. 900kHz 79. 976kHz 60. 000kHz 55. 930kHz 65. 290kHz 67. 43kHz 60 Hz 72 Hz 75 Hz 56 Hz 60 Hz 72 Hz 75 Hz 60 Hz 70 Hz 72 Hz 75 Hz 60 Hz 70 Hz 72 Hz 75 Hz 60 Hz 60 Hz 60Hz 60Hz 21 CONNECTOR PINASSIGNMENT 15 - Pin Color Display Signal Cable PINNO. 8. DESCRIPTION Red Green Blue Ground Ground R-Ground G-Ground B-Ground PINNO. 15. DESCRIPTION +5V Detect Cable Ground DDC-Serial Data H-Sync V-Sync DDC-Serial Clock 22 Display port connector (CN500) Pin ­ Assignment of 20-pin Display Port PIN NO. [. . . ]