User manual PLANAR LC1200R

[. . . ] LC1200R High-Bright Monitor USER'S MANUAL www. planar. com TABLE OF CONTENTS 1 2 2. 1 2. 2 2. 3 2. 4 2. 5 2. 6 2. 7 2. 8 2. 9 2. 10 2. 11 INTRODUCTION BASIC CONSTRUCTION LCD Display Weight Mechanical Cooling Fans Connectors Interface Cables Power Supply LCD Controller Board Inverter Board Photodiode Board Button Board 4 4 4 5 5 7 7 7 8 8 8 8 9 3 3. 1 3. 2 3. 3 3. 4 ENVIRONMENTAL Temperature and Humidity Direct Sunlight Operation Altitude Mechanical Vibration and Shock 9 9 10 10 10 4 4. 1 4. 2 4. 3 4. 4 4. 5 VIDEO SIGNAL REQUIREMENTS Video Input Lines Signal Functions Signal Quality Timing and Frequency Video Signal On-Off Sequences 11 11 11 14 15 15 5 5. 1 5. 2 5. 3 DC POWER INPUT REQUIREMENTS DC Power Input Lines DC Input Voltage / Current Power On-Off Sequences 16 16 16 17 6 6. 1 6. 2 6. 3 USER CONTROLS LCD Controller Board Controls User Adjustments Dimming 17 17 18 20 7 7. 1 7. 2 MONITOR PERFORMANCE Monitor Luminance Display Contrast 22 22 22 LC1200R User's Guide 021-0183-00 Rev A 2 of 29 7. 3 7. 4 Display Uniformity Display Chromaticity 23 23 8 8. 1 8. 2 DISPLAY COSMETICS Black Display Picture Mode White Display Picture Mode 24 24 24 9 9. 1 9. 2 9. 3 9. 4 9. 5 9. 6 REGULATORY AGENCY REQUIREMENTS Safety Certification CE Marketing RFI Emission Certification System Transient Disturbance Requirements Labeling ROHS Compliance 24 24 24 25 25 25 26 10 RELIABILITY 10. 1 10. 2 Design Workload MTBF 26 26 26 11 DESCRIPTION OF WARRANTY 12 SUPPORT AND SERVICE 13 GLOSSARY OF TERMS 26 27 28 LC1200R User's Guide 021-0183-00 Rev A 3 of 29 1 Introduction This document defines the electromechanical parameters and operating characteristics for The Planar Systems, Inc. LC1200R, Very High Bright, 12. 1" Active Matrix Liquid Crystal Display (AMLCD) based product. It is intended for operation as a component in a high ambient light, outdoor system. The LC1200R has a scaleable video format capable of displaying a minimum of VGA (640 x 480) through XGA (1024 x 768) input resolution. [. . . ] The direction will continue to be true until the maximum or minimum adjustment is reached. If the button is held down, the position will continuously adjust until released. The direction of the adjustment depends on the direction of the last adjustment. The direction will continue to be true until the maximum or minimum adjustment is reached. At this point, the direction will reverse LC1200R User's Guide 021-0183-00 Rev A 17 of 29 The Gain adjustment is to allow the full scale of the input video to be utilized. The direction of this adjustment will reverse when a limit is reached. For example, it will adjust from maximum to minimum, then reverse and go from minimum to maximum. The best way to make this adjustment is with a continuous gray scale pattern on the display. Auto Adjust: All four parameters (clock, Horizontal position, Vertical position, and gain) can be adjusted automatically by pressing the Horz and DotClk+ button simultaneously. For best results, display a pattern containing white and black with some white pixels along all four edges while the auto adjust is performed. 6. 2 User Adjustments There are features that allow the user to adjust the properties of the LC1200R. These adjustments will require access to the video board PCB and the inverter. Access to the Photodiode Connector Section 2. 5. 3 and Dimming Control Connector Section 2. 5. 4 can be gained by removing 1 screw and a small access panel. ESD precautions should be taken when removing this panel or the back cover of the unit. Figure 6: Remove Screw and Door 6. 2. 1 Flip and Mirror The unit has the capability to flip and/or mirror the video image. This can be done to allow for the power and video connector to be located on the other side of the unit for flexibility in mounting the LC1200R. See Section 7 for view angle. LC1200R User's Guide 021-0183-00 Rev A 18 of 29 6. 2. 2 Max Bright Jumper The photodiode board can be removed from the system. When the photodiode board is unplugged the LC1200R will default to the minimum brightness mode. If the user would like to display to run at maximum brightness, the MAX BRIGHT, JP1, jumper must be inserted on the inverter board. See Figure 8 Figure 7 Install jumper to flip Install jumper to Mirror Figure 8 Insert Jumper for Max Brightness LC1200R User's Guide 021-0183-00 Rev A 19 of 29 6. 3 Dimming 6. 3. 1 Photodiode Board and Automatic Dimming Connector The photodiode board must be mounted in the user's system so that the photodiode is exposed to the ambient light. In dark conditions, the LC1200R will adjust to approximately 25% of the maximum luminance. Connector Pin Assignments are in Table 8 Table 8 Pin 1 2 3 Description Output from photodiode anode 5V input from the LC12F for photodiode cathode No connection 6. 3. 2 Dimming Control Connector Pin Assignment and Performance A separate connector will allow dimming via an analog input and will allow the inverter to be inhibited. A 5V reference and ground are provided for cases where an external potentiometer is used to generate the DIM input. [. . . ] In three-dimensional CIE color space, chrominance is a vector which lies in a plane of constant luminance. Chromaticity: The color quality of light which is defined by its dominant wavelength and purity (see Chrominance). Chromaticity Value: The scalar value of any one component of a three-component color (also called a tristimulus value). The unit value of each component is the amount of that component added to the other two components to produce a reference "white". [. . . ]