User manual PLANAR FWT1744NU Product Manual

[. . . ] Connect the equipment into an outlet different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Caution: To comply with the limits for an FCC Class B computing device, always use the shielded signal cord supplied with this unit. The Federal Communications Commission warns that changes or modifications of the unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. CE mark for Class B ITE (Following European standard EN55022/1998; EN61000-3-2/1995; EN61000-3-3/1995, EN55024/1998, EN60950/1992+A1+A2+A3+A4+A11) Radio Frequency Interference Statement Warning: This is a Class B product. In a domestic environment, this product may cause radio interference in which case the user may be required to take adequate measures. i Planar User's Manual Canadian Doc Notice For Class B Computing Devices This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the Radio Interference Regulation of the Canadian Department of Communications. [. . . ] VGA Cable Connector Connect the supplied 1. 5m 15-pin D-Sub VGA cable to this connector. The opposite end of the cable is connected to your PC's graphics card. 2 Chapter 1 Adjusting the Monitor's Position Your LCD monitor's tilting angle can be adjusted in the landscape. Adjusting the Tilting Angle The LCD monitor's angle settings range from -5° to 25°in the landscape. Forcing the monitor past its maximum extension can result in damage to the monitor. Connecting AC Power Refer to the following instructions for connecting AC power to the LCD monitor. Plug the female end of the power cable into the AC-adapter and the male end of the power cord into a wall socket. The plug on the power cable will vary according to the electrical standard for your area. Plug the adapter power connector into the LCD monitor's DC power jack. 3 Planar User's Manual Connecting Video 1. Turn off your PC and the LCD monitor before connecting your LCD monitor to the computer. Loop the 1. 5M VGA cable through the hole in the LCD monitor's stand and plug it into the LCD monitor' s VGA cable connector. Tighten the connecting screws. Connecting the Stereo Speakers Please refer to the following instructions for connecting the LCD monitor's stereo speakers. Connect the 1. 5M audio cable to the line-out of your PC's sound card. Connect the other end to the LCD monitor's audio line-in jack. 3. You can adjust the sound volume of the stereo speakers by using the speaker volume control function in the OSD (On-Screen Display). See the next chapter for details. 4 Chapter 1 Power Management System The LCD monitor complies with the VESA DPMS power management proposal. Adjusting these settings should only be necessary if the results from Auto-Adjust function are not satisfactory. The OSD-Control option allows you to adjust the position and setting of the monitor's On Screen Display. The MISC-Control option allows you to select the desired text language of the OSD, adjust the monitor speaker volume, and to display the current video information being sent to the monitor from your video card. The Graphic-Control option allows you to adjust the display contrast, brightness, sharpness, and color settings. The Graph/Tex option allows you to switch DOS text resolution from 640x400 and 720x400. This function has no effect within graphic operating systems such as MS WindowsTM. The OSD Exit option closes the On Screen Display. 7 Planar User's Manual Auto Adjust Procedure Pressing the Adjust key while the Auto Adjust topline menu is selected, activates the Auto Adjust procedure. Once finished, the OSD menu will disappear after a short time-out period. The Monitor- Control Option Pressing the Adjust key while the Monitor Control icon is selected activates the Monitor Control submenu. You should only use this menu item if the results of the Auto Adjust function are not satisfactory. H-Position: Press the V-Position: Press the Adjust Adjust buttons to horizontally move the display image to the desired position. buttons to vertically move the display image to the desired position. Phase: Press the Adjust buttons to fine-tune the displayed image. An improper phase adjustment will result in pixel jitter or display noise. Clock: Press the Adjust buttons to stabilize the display clock timing. An improper clock setting will result in wide vertical bands on the display. Reset: Press the Adjust Exit: Press the Adjust button to reset the Monitor-Control submenu values to the factory default values. button key to exit the Monitor-Control submenu. OSD - Control Option Pressing the Adjust key while the OSD Control icon is selected activates the OSD Control submenu. [. . . ] Press the OSD Menu button (refer to Chapter 2) once and then press either Adjustment Control button several times. If there is still no display, press the other Adjustment Control button several times. If step 2 doesn't work, connect your PC system to another external CRT. If your PC system functions properly with a CRT monitor but it does not function with the LCD monitor, and the LCD monitor's power LED is blinking, the output timing of the PC's VGA card may be out of the LCD's synchronous range. [. . . ]