User manual PHILIPS CP9239

[. . . ] General -- The shaver is equipped with an automatic voltage selector and is suitable for mains voltages ranging from 100 to 240 volts. €2) 1 2 3 4 5 6 7 8 9 Protection cap Shaving unit Shaver on/off slide Charging light (HQ6996, HQ6990, HQ6986, HQ6976, HQ6950, HQ6947, HQ6927, HQ6926, HQ6925, HQ6923 only) Trimmer (HQ6996, HQ6990, HQ6976, HQ6950, HQ6946 only) Trimmer slide (HQ6996, HQ6990, HQ6976, HQ6950, HQ6946 only) Cleaning brush Mains cord with plug Appliance plug ENGLISH Charging Charge the appliance: -- before first use and when you have not used the appliance for a long time -- when the motor stops or starts running slower When you have charged the shaver for the first time and after a long period of disuse, optimise the battery capacity in the following way: 1 Fully charge the shaver and then use it normally until the battery  is completely empty. If you optimise the battery capacity in this way, you can also charge the shaver in between shaves, even if the battery is not completely empty yet. Charging the shaver (HQ6996, HQ6990, HQ6986, HQ6976, HQ6950, HQ6947, HQ6927, HQ6926, HQ6925, HQ6923 only) Quick charge (HQ6996, HQ6990, HQ6986 only) After the shaver has charged for 3 minutes, it contains enough energy for one cordless shave. [. . . ] 4 Clean the inside of the shaving unit and the hair chamber with the cleaning brush. Remove the mains plug from the wall socket and pull the appliance plug out of the shaver. 3 Turn the wheel anticlockwise (1) and remove the retaining frame (2). 4 Remove the shaving heads (cutters and guards) one by one and clean them with the cleaning brush supplied. Note: Do not clean more than one cutter and guard at a time, since they are all matching sets. If you accidentally mix up the cutters and guards, it may take several weeks before optimal shaving performance is restored. 5 Clean the cutter with the short-bristled side of the cleaning brush. Put the retaining frame back into the shaving unit, push it down (1) and turn the wheel clockwise (2). Extra-thorough cleaning For extra-thorough cleaning, put the shaving heads in a degreasing liquid (e. After cleaning, lubricate the central point on the inside of the guards with a drop of sewing machine oil to prevent wear of the shaving heads. Trimmer (HQ6996, HQ6990, HQ6976, HQ6950, HQ6946 only) Clean the trimmer every time you have used it. Remove the mains plug from the wall socket and pull the appliance plug out of the shaver. Tip: Lubricate the trimmer teeth with a drop of sewing machine oil every six months. 10 ENGLISH Replacement Replace the shaving heads every two years for optimal shaving results. Remove the mains plug from the wall socket and pull the appliance plug out of the shaver. 3 Turn the wheel anticlockwise (1) and remove the retaining frame (2). 5 Put the retaining frame back into the shaving unit, push it down (1) and turn the wheel clockwise (2). You can also contact the Philips Consumer Care Centre in your country (see the worldwide guarantee leaflet for contact details). The following accessories are available: -- HQ56 Philips Shaving Heads -- HQ110 Philips Shaving Head Cleaning Spray ENGLISH Environment 11 -- Do not throw away the appliance with the normal household waste at the end of its life, but hand it in at an official collection point for recycling. -- The built-in rechargeable battery contains substances that may pollute the environment. Always remove the battery before you discard and hand in the appliance at an official collection point. If you have trouble removing the battery, you can also take the appliance to a Philips service centre. [. . . ] For at få fuldt udbytte af den support, Philips tilbyder, skal du registrere dit produkt på www. -- Apparatet bør holdes uden for børns rækkevidde for at sikre, at de ikke kan komme til at lege med det. Sikkerhed og support Hvis du har brug for hjælp eller support, bedes du besøge www. Close Cut-systemet sørger for en tett og enkel barbering hver dag. [. . . ]