User manual PHAROS IGPS-BT II

[. . . ] iGPS-BT II will need to be charged for approximately 3 hours before initial use. - On/Off Switch Turns the iGPS-BT II on or off. Blue LED's will light up when powered. Bluetooth Status Indicator (Internal Blue LED) Blinking: Searching for Bluetooth signal. Steady: Bluetooth communication established, ready to use. Battery charging Indicator (Orange/Green LED) Orange: Battery is being charged. iGPS-BT II Setup (see walkthrough guides at the end of this section) 1. [. . . ] Tap the Bluetooth icon in the lower right-hand corner and select "Bluetooth Manager" 2. To create a shortcut, tap on "New", "Connect" (For some devices, you may not need to select "Connect" before proceeding to the next step) 3. Select "Explore a Bluetooth device", and tap on "Next" 4. To create the connection to the Pharos iGPS-BT II, select: "Tap here to choose a device" 4 5. Provided that your iGPS-BT II is turned on and fully charged, it will be discovered. Enter the Passkey: 12345678, and select "OK" in the upper right-hand corner 7. Select "GPS RFcom" so that it becomes highlighted, and tap on "Next" 8. Tap on "Finish" 5 9. Tap and hold on the "Pharos iGPSBT: GPS RFcom" icon, select "Connect" from the Menu that appears 10. You will also notice that the Blue light on the GPS itself is now a solid, steady Blue. 11. Open Pharos Ostia on your Pocket PC, click through the Warning screens, and tap on "Tools", "Options". . . 12. To select the appropriate COM Port for your Pocket PC (with built-in Bluetooth Technology), refer to the list here: iPAQ 22XX/51XX/54XX/55XX ­ COM8 iPAQ 41XX/43XX ­ COM6 iPAQ 194X ­ COM5 Dell Axim X3i/X30 ­ COM7 Toshiba e80X ­ COM6 ASUS A620BT/A716 ­ COM6 HTC XDAII ­ COM4 6 13. Now that the COM Port is setup, you can Enable the GPS by tapping on the RED Smiley face 14. Select "YES" to Enable the GPS Bluetooth setup for Windows Mobile 5. 0 OS 7 2. iGPS-BT II Setup for Pocket PCs with built-in Bluetooth Technology running the Windows Mobile 5. 0 OS (the following screen shots show the device as "Pharos iGPS-BT", it might be shown as "Pharos BT GPS II" on your Pocket PC. ) 2. Click the small Bluetooth icon the bottom right-hand side of the screen. 3. Then click on the "Devices" tab on the bottom of the screen. When the device finishes searching, you should see "?Pharos iGPS-BT" in the box. Put a check mark in the box next to "serial port" and tap Finish 8. Next select the "COM Ports" tab at the bottom of the screen. Select Com 7, and make sure that there is a check in the "Secure Connection" box and tap Finish. 11. Close down the Bluetooth Settings screen and start the Pharos Ostia navigation program. Start > Programs > Ostia If starting Ostia for the first time, you will be asked for the registration code which can be found printed inside the case the CDs came in. 12. [. . . ] Dropping the receiver, heavy impact, or excess vibration may cause damage or malfunction. Any return(s) that were not purchased directly from Pharos, please contact the reseller where it was purchased from. · All defective returns for either repair or replacement will be processed and returned to the customer within 3 business days of receipt. For items beyond the 1year warranty, a repair charge of $35 to $50 or a replacement charge of $95 to $150 will be due. [. . . ]