User manual PET SAFE ELECTRONIC PET FEEDER

[. . . ] com/Ce/ DJ-S17E: VHF FM Transceiver 144. 000~145. 995MHz DJ-S47E: UHF FM Transceiver 430. 000~439. 995MHz This device is authorized for use in all EU and EFTA member states. No part of this document may be reproduced, copied, translated or transcribed in any form or by any means without the prior written permission of Alinco. Inc. , Osaka, Japan, English Edition Printed in Japan. 3 Warning Warning To prevent any hazard during operation of Alinco's radio product, in this manual and on the product you may find symbols shown below. Please read and understand the meanings of these symbols before starting to use the product. d Danger d Alert d Caution d a m d Alert This symbol is intended to alert the user to an immediate danger that may cause loss of life and property if the user disregards the warning. [. . . ] To change the values instead, repeat the same setting sequence explained on page 26 for shift direction and offset frequency then page 37 for CTCSS tone by entering to the Set mode while is displayed. Even if you desire the same values you set for the respective parameters in the VFO mode, please repeat the sequence in here to activate the Repeater-Access function. After having completed the programming in the Set mode, return to the menu by pressing any key except FUNC or MONI. You can not delete or convert this memory to other purposes. 4 4. 5. 6 Programmable Parameters in Memory Channels The following parameters can be stored in each of the memory channels. · Frequency · Offset frequency * · Skip channel setting · Shift direction (+/-) * · Busy channel lockout (BCLO) · Tone encoder frequency * · Transmission power (H/L) · Tone decoder frequency * · Battery save setting · Tone encoder/decoder setting (TSQ) * · Clock Shift setting · DCS code * · Alphanumeric channel tag · DCS setting * · Attenuator Level NOTE: Only parameters marked "*" are programmable in Repeater-Access function memory. 29 4. Basic Operation 4. 6 Call-Channel Mode This mode is used to recall a most frequently used memory channel (stored in MC channel) with a single key-touch. " " is displayed on the LCD, and the channel programmed in MC is recalled. Press the key again in the Call mode to return to original operating mode (VFO/memory). NOTE: Refer to "How to Program Call Channel" on page 28 for programming Call channel. 4 IMPORTANT NOTE: · The dial operation of frequency/memory channel is blocked in the Call mode. · It is possible to temporary change the offset and CTCSS/DCS related parameters in the Call mode by entering to the Set mode in the Call channel. · The CALL channel reprogramming is possible but it can't be deleted from the memory channel mode. 4. 7 Receiving 1. Press the key and rotate the dial to adjust the audio level as necessary. Rotate the dial clockwise/counter-clockwise to change the scan direction. NOTE: Please set the squelch level correctly before scanning, even in the TSQ scanning the normal squelch level adjustment is required to activate this function. 32 5. Useful Functions 5. 1. 3 Setting Skip Channels You can select the memory channels that you wish to skip during the memory-scan. Press the FUNC key for more than 2 seconds to enter the Set mode, and select the menu 16 to display the current skip channel setting. The 10MHz decimal point appears for the memory channel that is set as a skip channel. NOTE: The Call channel and Repeater-Access memory are automatically skipped during scanning. 5. 2 Keylock Press the key for more than 2 seconds to set the Keylock function on, and repeat the same to quit. When the Keylock is on, other than the following, all operations are blocked. * PTT * LAMP * MONI * VOL * SQL * Tone-burst * POWER ON/OFF NOTE: Keylock function can't be activated on the Repeater-Access function memory channel. 5 5. 3 Tone-Burst This function is to generate an audible tone to access repeaters mostly used in Europe. · To output the tone-burst tone, press the MONI key while holding down the PTT key. The initial setting for the tone-burst tone is 1750Hz, but this can be changed in the Set mode (page 44). · While transmitting the tone-burst tone, the CTCSS/DCS tone is temporary suspended. · Even while transmitting the tone-burst tone, you can not hear audio from the speaker. 33 5. Useful Functions 5. 4 Naming Memory Channels In the Memory mode, it is possible to display up to 6 alphanumeric characters (Nametag) instead of conventional frequency display. 5. 4. 1 Setting Name-Tag 1. [. . . ] Mount the battery (with or without being attached to the unit) in the basket as shown. The red indicator on the basket turns on and charging starts. 10 NOTE: You can charge the battery pack using a basket (EDC-143/144) even if the battery charge function is set to "CHG-OF". 56 10. Maintenance and Reference 5. After charging time is elapsed (page 54), remove the battery pack from the basket. The red indicator stays turned on as long as the pack is mounted on the basket regardless of the charging status. Specifications *The charging time may vary depending on the condition of the battery pack and the temperature of the environment. NOTE: Refer to page 59 for information about how to charge the battery using addtional baskets. Charging with the EDC-144 (Quick Charger) Please make sure that following items are included in the package · EDC-144E: EDC-144 basket, EDC-151 adapter (AC 230V), insulation sheet · EDC-144UK: EDC-144 basket, EDC-152 adapter (AC 230V), insulation sheet · EDC-144R: EDC-144 basket, connection cable, insulation sheet, 2 screws, connective stay Caution Before using them for the first time, attach the insulation sheet to cover the screw-terminals to avoid short-circuiting. [. . . ]