User manual PENTAX PCF II

[. . . ] Images taken with the purpose of obtaining copyrights also cannot be used outside the scope of use of the copyright as laid out in the Copyright Act, and care should be taken here also. To users of this camera · There is a possibility that recorded data may be erased or that the camera may not function correctly when used in surroundings such as installations generating strong electromagnetic radiation or magnetic fields. · The liquid crystal panel used in the LCD display is manufactured using extremely high precision technology. Although the level of functioning pixels is 99. 99% or better, you should be aware that 0. 01% or fewer of the pixels may not illuminate or may illuminate when they should not. [. . . ] Press the shutter release button. g The self-timer is engaged and the selftimer lamp lights for about seven seconds. The picture is taken approximately three seconds after the 7/ 7/2004 self-timer lamp starts to blink. 3:00 PM r The self-timer is engaged and the picture is taken approximately two seconds after the self-timer lamp starts to blink. Focusing may be compromised if you move the camera while the self-timer lamp is blinking. · To cancel the self-timer, press the MENU button while the second count is displayed. · In the 3D Image mode, both the first and second images will be taken with the self-timer engaged. Taking Pictures of Yourself 1p. 58 Troubleshooting "Subject is not in focus" 1p. 165 046 Shutter release button gh button Continuous Shooting (Continuous Shooting Mode) You can switch the drive mode to Continuous Shooting mode. Pictures are taken continuously while the shutter release button is pressed. 4 Taking Pictures 1 2 3 Press the gh button in the Capture mode to display j on the LCD monitor. Press the shutter release button halfway. The focus frame on the LCD monitor will light green when the camera is in focus. 046 7/ 7/2004 3:00 PM Press the shutter release button. Pictures are taken continuously while the shutter release button is pressed. Shooting stops when you take your finger off the shutter release button. · The interval will vary according to the [Recorded Pixels] and [Quality Level] settings. Mode] menu in this case. 2 Press the shutter release button. Interval shooting will start with the following settings. · Interval 0min 10sec · Number of shot 02 · Start time 0hr 0min The camera turns off automatically when shooting is finished. · Interval shooting can be set at intervals of 10 seconds to 4 minutes in units of 1 second, and intervals of 4 minutes to 99 minutes in units of 1 minute. · The number of pictures can be set in the range of 2 to 99 pictures. · If the start time is set to 0 min. , the first picture will be taken as soon as the shutter release button is pressed. · The remaining number of pictures and interval time will be displayed on the LCD monitor when you press the power switch on during standby. If you press the Menu button, the message "Stop interval shooting?" will be displayed. · Interval shooting stops and the camera turns off automatically when the SD Memory Card runs out of memory space. · You cannot add a voice memo to an image shot in interval shooting. · Interval shooting is not possible in the C F or G mode. 4 Taking Pictures Setting the interval, number of shot, and start time 1 2 3 Press the Menu button in the Capture mode. The [A Rec. Mode] menu will be displayed. Press the four-way controller (23) to select [Interval Shoot]. Press the four-way controller (5). The Interval Shooting menu will be displayed. Interval Shoot Interval 00min 10sec Number of Shot 02 Start Time 00hr 00min MENU 4 5 Cancel OK OK Press the four-way controller (45) to select O (On)/P (Off) and press the four-way controller (3). Press the four-way controller (5). [Interval] is selected. 77 6 Set the interval time. 1. [. . . ] This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ]