User manual PENTAX PC-330

[. . . ] However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Use of shielded cable is required to comply with Class B limits in Subpart B of Part 15 of the FCC rules. [. . . ] Use to select [Drive Mode], then press the button. Mode1 Focus Drive Mode AE Metering Mode2 Mode3 Std. OK: Exit : 2/3 4. Press the shutter button to capture the image. button. Std. Drive Mode HS Continuous Auto Bracket OK : Exit : 2/3 In High Speed Continuous mode, the flash mode will be set to OFF automatically. EN-34 Auto Bracket In this mode, the camera automatically changes the exposure within a set range to take three shots after you press the shutter button once. Auto Bracket settings can be combined with exposure compensation settings to extend the adjustment range. HS Continuous Auto Bracket OK : Exit : 3/3 In Auto Bracket mode, the flash mode will be set to OFF automatically. EN-35 Selecting the Metering Mode You can select the metering mode that sets which part of the subject to measure to determine the exposure. Use to select [AE Metering], then press the Mode1 Focus Drive Mode AE Metering Mode2 Mode3 Std. OK : Exit : 3/3 4. [ Center-weight]: Averages the light metered from the entire frame, but gives greater weight to the subject matter at the center. [ Spot]: The exposure is determined by the small area in the center of the screen only. Press the shutter button to capture the image. AE Metering Center-weight Spot OK : Exit : 1/2 EN-36 PLAYBACK MODE - THE BASICS Viewing Images You can display the still image you have just captured at a time. Rotate the mode dial to , , , , , or and turn your camera on by pressing the button. '04 1280X960 +1. 7 05:22 1 The playback information displayed on the LCD monitor will disappear after 2 seconds. If there is no image stored in the internal memory or on the memory card. The method of operation is the same as playing back still images and movie clips on the digital camera. PC/AV terminal The sound recorded with movie clips can only be played back on TV or computers. EN-44 Deleting Images/Movie Clips Use this function to delete one or all images/movie clips stored in the internal memory or memory card. Please note that the deleted images or movie clips cannot be recovered. Exercise caution before deleting a file. To delete the latest single image/movie clip 1. Rotate the mode dial to , , , , , or and turn your camera on by pressing the button. When the delete message appears, use or to select [OK], then press the button to delete the last image or movie clip. If you wish to cancel the deletion, select [Cancel]. Delete OK Cancel OK : To delete image/movie clip by preference 1. Rotate the mode dial to , , , , , or and turn your camera on by pressing the button. The last recorded image appears on the LCD monitor, which can also be deleted directly by pressing the button. Press the MENU button, then use or to select [Delete] and press the button. When the delete message appears, use or to select [OK], then press the button to confirm the deletion. If you wish to cancel the deletion, select [Cancel]. Playback Delete Slideshow Protect Quality Change OK : Exit : 1/7 Delete This Image Delete All OK : Return : Protected images cannot be deleted with the delete function. EN-45 Protecting Images/Movie Clips Set the data to read-only to prevent images from being erased by mistake. [. . . ] Image is not captured when the shutter button is pressed. Flash does not fire. Continuous shooting is not possible. Cannot transfer files over a USB connection. * NO FLASH is selected in flash mode. * The camera is in the * The capacity of the built-in memory or SD memory card is full. * Camera is turned off. EN-72 Possible Number of Recordable Images The frame counter indicates the approximate number of images that can be stored on the internal memory and the SD memory card. [. . . ]