User manual PENTAX OPTIO 60

[. . . ] FCC STATEMENT (For customers in USA) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. [. . . ] Press the shutter button to capture the image. Select: Av/Tv F2. 8 2s OK : Press the shuter button halfway to confirm if the exposure is set correctly on the LCD monitor. EN-34 ADVANCED SHOOTING High Speed Continuous This mode is used for continuous shooting. Use to select [Drive Mode], then press the Mode1 Mode2 Mode3 AE Metering Drive Mode Digital Zoom Instant Review OK: Exit : On Off 2/4 4. To exit the menu, press the MENU button. button. Drive Mode Standard HS Continuous Auto Bracket The indicator is displayed on the monitor screen. Press the shutter button to capture a sequence of images. OK : Exit : 2/3 In High Speed Continuous mode, the flash mode will be set to OFF automatically. EN-35 Auto Bracket In this mode, the camera automatically changes the exposure within a set range to take three shots after you press the shutter button once. Auto Bracket settings can be combined with exposure compensation settings to extend the adjustment range. Press the shutter button to capture the three images. Drive Mode Standard HS Continuous Auto Bracket OK : Exit : 3/3 In Auto Bracket mode, the flash mode will be set to OFF automatically. EN-36 Selecting the Metering Mode You can select the metering mode that sets which part of the subject to measure to determine the exposure. Use to select [AE Metering], then press the Mode1 Mode2 Mode3 AE Metering Drive Mode Digital Zoom Instant Review OK: Exit : On Off 1/4 4. [ Center-Weighted]: Averages the light metered from the entire frame, but gives greater weight to the subject matter at the center. [ Spot]: The exposure is determined by the small area in the center of the screen only. Press the shutter button to capture the image. AE Metering Center-Weighted Spot OK : Exit : 1/2 EN-37 PLAYBACK MODE - THE BASICS Viewing Images You can display the still images one by one. '05 2848X2136 +1. 7 05:22 1 The playback information displayed on the LCD monitor will disappear after 2 seconds. (Refer to EN-47 for further details. ) For protected images/movie clips, mark will be displayed. (Refer to EN-48, 49 for further For images selected for printing with DPOF setting, details. ) If there is no image stored in the internal memory or on the memory card. [No Image] message will appear on the monitor. EN-38 Magnifying Images While reviewing your images, you may enlarge a selected portion of an image. The zoom factor displayed on the screen shows the current magnification ratio. Adjust the zoom ratio by using the Zoom To enlarge the selected image, press the button. To return to the normal image, press the The magnification factor is displayed on the LCD monitor. To view different portions of the images, press / / / to adjust the display area. 1. 5X The magnification factors range from 1x to 4x (within 7 stages: 1. 0x, 1. 5x, 2. 0x, 2. 5x, 3. 0x, 3. 5x and 4. 0x). EN-39 Thumbnail Display This function allows you to view 9 thumbnail images on the LCD monitor simultaneously so you may search for a particular image. Use / / / to move the cursor to select the image to be displayed at regular size. Press the button to display the selected image on full screen. 1 2 5 7 EN-40 Slideshow Display The slide show function enables you to play your images back automatically in sequential order. This is very useful and entertaining feature for reviewing recorded images and for presentations. press the PlayBack1 Slideshow Protect DPOF PlayBack2 OK : Exit : 1/3 3. [. . . ] In this case, it will take a considerable length of time before the equipment can be returned to you owing to the complicated customs procedures required. If the equipment is covered by warranty, repairs will be made and parts replaced free of charge, and the equipment will be returned to you upon completion of servicing. If the equipment is not covered by warranty, regular charges of the manufacturer or of its representatives will apply. EN-76 If your PENTAX was purchased outside of the country where you wish to have it serviced during the warranty period, regular handling and servicing fees may be charged by the manufacturer's representatives in that country. [. . . ]