User manual PENTAX MZ-30

[. . . ] angle function 4. 6 Station setup [By Polar Coordinates] 4. 7 Station Orientation 4. 8 Measuring 4. 9 Offset 5 View and Edit 5. 1 Graphical View 5. 2 Create the Rectangular Point 5. 3 Edit the Data 6 Free Stationing 6. 1 Stationing by more than 3 known points 6. 2 Stationing by two known points 7 Stake Out 7. 1 Stake Out 7. 2 Point to Line 8 Calculations 8. 1 Inverse 8. 2 2D SURFACE 8. 3 REM 48 49 49 50 51 52 52 53 53 55 56 57 58 61 62 63 65 68 71 72 74 75 76 76 77 78 79 81 84 84 87 90 90 93 96 >> 6 CONTENTS >> 9 RDM (Remote Distance Measurement) 9. 1 PH input 9. 2 Reference point - Target distance 9. 3 Target - Target distance 9. 4 New Reference point selection 10 Transfer 10. 1 Input from the PC 10. 2 Output to the PC 10. 3 Communication setup 10. 4 About DataLink DL-01 Software 11 Preference 11. 1 Language selection 11. 2 Coordinate axis definition 11. 3 Input method selection 11. 4 Action method selection 11. 5 Remote method selection 11. 6 Compare method selection 11. 7 Request aiming selection 11. 8 Elevation Factor 11. 9 Duplicate Point Check Function List 97 98 98 99 100 100 101 102 103 107 108 109 109 111 113 114 115 116 117 118 119 7 PRECAUTIONS REGARDING SAFETY Safety precautions (Must be followed) The following items are intended to prevent possible injury to the user or other people and/or damage to the instrument before it occurs. These safety precautions are important to the safe operation of this product and should be observed at all times. Distinctive displays The following displays are used to distinguish precautions by the degree of injury or damage that may result if the precaution is ignored. WARNING Items indicated by this sign are precautions which, if ignored, would result in serious injury. CAUTION Items indicated by this sign are precautions which if ignored may result in injury or material damage. · Here "injury" refers to injuries such as cuts, burns or electric shock the treatment of which will not likely require hospitalization or long-term attention. · "Material damage" refers to damage to facilities, buildings, acquired data, etc. [. . . ] · The Power Topo Express screens vary with the chosen settings under "9. · The MZ-30 series instrument has the Job name "PENTAX" as its default setting. And therefore, the data is stored in the "PENTAX" Job by default, unless another new Job name is created. When another Job name is created, the data is stored in the new Job name. · The input range of the X, Y and Z Coordinate is "-99999999. 998" - "+99999999. 998" . · The input range of the Instrument and Prism height is "-9999. 998" - "+9999. 998" . · The PC is added together with the PN, Coordinates X, Y, Z and IH (PH or HI) in the STATION POINT SETUP screen. If you have a PointCodeList saved in the job named "POINTCODELIST" , you can easily select one of the PointCodes from that list or edit one of them after pressing [ENT] while "6. Please, note that a PointCode which is saved in a job with any other name can not be selected from a list. · There are two coordinate types: Rectangular and Polar Coordinates. The VO, TO offset and the remote measurement function are only available when you use Rectangular Coordinates. Select your desired Job name and press to confirm your selection. 3. 3. 2 Selection by a Job name input Select "2. JOB NAME SEARCH" by pressing . · The JOB NAME SEARCH uses your input to search the entire job list. JOB NAME SEARCH Press to view the JOB NAME INPUT screen. JOB NAME INPUT ABCDEFGHIJKLMNOPQRSTUVWXYZ abcdefghijklmnopqrstuvwxyz 0123456789. , ?!()":;+-*/&=%# BS CLEAR ACCEPT Input your desired JOB NAME and press JOB LIST SEARCH to view the JOB LIST SEARCH screen. 1. TOKYO Select your desired Job name and press to confirm the selection. 54 3. 4 Deletion of a Job name Select "4. DELETE" with or and press to view the JOB SELECTION screen. JOB SELECTION 1. JOB LIST SEARCH" and press to view its screen. JOB LIST SEARCH 1. Select the Job name that needs to be deleted and press , then the DELETION CONFIRMATION SCREEN is displayed. Press [ENT] to confirm Press [ESC] to abort. to delete or to abort. 3. 4. 2 Deletion using "Job name search" Select "2. JOB NAME SEARCH" by pressing . · The JOB NAME SEARCH uses your input to search the entire job list. JOB NAME SEARCH 55 Press to view the JOB NAME INPUT screen. JOB NAME INPUT ABCDEFGHIJKLMNOPQRSTUVWXYZ abcdefghijklmnopqrstuvwxyz 0123456789. , ?!()":;+-*/&=%# BS CLEAR ACCEPT Input your desired JOB NAME and press JOB LIST SEARCH to view the JOB LIST SEARCH screen. 1. TOKYO Select the Job name that needs to be deleted and press , then the DELETION CONFIRMATION SCREEN is displayed. [. . . ] STRUCTURE TYPE INPUT METHOD: FULL TEMPLATE ACTION METHOD: PROCESS TYPE REMOTE METHOD: FIXED PLANE ACCEPT Process type This input method takes over functionality of "Power Topo Express" When this option is selec. ted, the next screen will be shown after inputting the necessary items. PN: X: Y: Z: IH: + 00000000. 000 m + 00000000. 000 m + 00000000. 000 m + 0000. 000 m LIST ACCEPT SAVE 113 Structure type This input method takes over classic functionality of our product. When this option is selected, the menu screen will be shown after inputting necessary items. RECTANGULAR COOR. 1. [. . . ]