User manual PENTAX ESPIO 120MI

[. . . ] Please take care, as there are even cases where limitations are placed on taking pictures even for personal enjoyment during demonstrations, performances or of items on display. Images taken with the purpose of obtaining copyrights also cannot be used outside the scope of use of the copyright as laid out in the Copyright Act, and care should be taken here also. Regarding trademarks · PENTAX and smc PENTAX are trademarks of PENTAX Corporation. · All other brands or product names are trademarks or registered trademarks of their respective owners. [. . . ] Mode Image Tone Recorded Pixels Quality Level Saturation Sharpness Contrast Cancel OK OK 113 Setting the Saturation/Sharpness/Contrast Select from five levels of Saturation, Sharpness and Contrast. The default setting is [0 (Standard)] for all. Saturation Sharpness Contrast Sets the color saturation. Sets the image contrast. Set [Saturation], [Sharpness] and [Contrast] in the [A Rec. (p. 100) Settings cannot be changed in Picture mode and H mode (p. 47). Rec. Mode Image Tone Recorded Pixels Quality Level Saturation Sharpness Contrast Exit Towards + : Higher saturation Towards ­ : Lower saturation 5 Function Reference Rec. Mode Image Tone Recorded Pixels Quality Level Saturation Sharpness Contrast Exit Towards + : Higher sharpness Towards ­ : Lower sharpness Rec. Mode Image Tone Recorded Pixels Quality Level Saturation Sharpness Contrast Exit Towards + : Higher contrast Towards ­ : Lower contrast 114 Setting the White Balance The color of the subject changes with the light source. For example, the same white object will be a different shade of white in daylight than under a light bulb. In cameras using film, this is adjusted by changing the film or using filters. The default setting is F (Auto). F Auto Daylight Shade Cloudy Fluorescent Light Tungsten Light Flash Manual Automatically adjusts the white balance. (About 6000K) For use when taking pictures under fluorescent lighting. Corrects sensitivity automatically in the range of ISO 200 to 3200. Set in [ISO Corction in AUTO] in the [A Custom Setting] menu. (p. 102) ISO Corction in AUTO ISO ISO ISO ISO 200-800 200-400 200-1600 200-3200 Corrects sensitivity automatically in the range of ISO 200 to 800 118 Sensitivity is not corrected in the following. · Exposure mode is a (Manual) or p (Bulb) mode · Flash is discharged · Auto bracketing · EV Compensation ISO Sensitivity Warning Display ISO Sensitivity Warning appears in the viewfinder when a sensitivity value of your choice is reached or exceeded. Set a sensitivity that is not regularly used to avoid forgetting to reset when sensitivity is raised. ISO Sensitivity Warning is not displayed by default. 1 2 Off ISO 400 ISO 800 ISO 1600 ISO 3200 ISO Sensitivity Warning is not displayed. ISO Sensitivity Warning is displayed when ISO 1600 is set or exceeded. ISO Sensitivity Warning is displayed when ISO 3200 is set. 5 3 4 5 Function Reference Set in [ISO Snstvty Wrn Dspl] in the [A Custom Setting] menu. (p. 102) ISO Snstvty Wrn Dspl Off ISO ISO ISO ISO 400 800 1600 3200 ISO sensitvty wrning not displayed in vewfnder o (ISO Sensitivity Warning) appears in the viewfinder when the set sensitivity is set or exceeded. ISO Sensitivity Warning is not displayed if sensitivity is automatically corrected (p. 117). 119 Setting the Color Space You can set the color space to use. The default setting is [sRGB]. 1 2 sRGB AdobeRGB Sets to sRGB color space. Sets to AdobeRGB color space. Set in [Color Space] in the [A Custom Setting] menu. (p. 103) Color Space sRGB AdobeRGB Sets to sRGB color space 5 Function Reference File names differ depending on the color space setting as shown below. [. . . ] These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. [. . . ]