User manual PENTAX EI100

[. . . ] For customers in the USA STATEMENT OF FCC COMPLIANCE This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. [. . . ] The cursor returns to the SETUP MENU. 14 Operating Modes and Menus CAPTURE Mode Set the Operating Mode Dial to CAPTURE for image capturing. Select the item by the arrow buttons ( / ) and then press the OK button to confirm. The cursor returns to the CAPTURE menu automatically when the change is made. The setting is conserved even if the camera power is off. CAPTURE Menu Press the Menu button in CAPTURE mode, the Capture menu appears. The menu contains the following items: LCD BRIGHTNESS: Changes the brightness setting ( -5 ~ +5 , Interval = 1 ) of the LCD display. The cursor returns to the CAPTURE menu automatically when the change is made. The setting is conserved even if the camera power is off. WHITE BALANCE: Select either one of the 5 (Auto, Daylight, Shade, Fluorescent, Tungsten) white balance settings. For certain critical circumstances, if the result did not come out as expected, you may manually change to another white balance type according to the ambient lighting condition. 15 Select the item by the arrow buttons ( / ) and then press the OK button to confirm. The cursor returns to the CAPTURE menu automatically when the change is made. This setting is reset to AUTO when the camera power is off. increase/decrease the EV compensate value (-2. 0 ~ +2. 0). The cursor returns to the CAPTURE menu automatically when the change is made. This setting is reset to O. O when the camera power is off. DIGITAL ZOOM: Press the DISPLAY button. In CAPTURE mode, you can see the close-up effect on the LCD Monitor by pressing the OK button to activate 2X digital zoom function. Digital Zoom is only available in the 1280x960 recording pixels. Reference: The approximate color temperature of the 4 above white balance settings (except Auto White Balance) will be Daylight = 5500K, Shade= 6000K, Tungsten = 2850K and Fluorescent = 4000K. EV COMPENSATION: Adjusts the exposure compensation over a range of -2. 0 to +2. 0 EV in steps of 0. 3 EV, where 1. 0 EV = 1 f-stop. Select the item by the arrow buttons ( / ) and then press the OK button to confirm. Use the arrow buttons ( / ) to 16 PLAY Mode In Play mode, users can review the captured images on the LCD Monitor or on a TV. Set the Operating Mode Dial to PLAY for image review. Play Menu Press the Menu button in PLAY mode, the Play menu appears. The menu contains the following items: to increase/decrease the delay between 2 and 10 seconds. The slide show starts. Do not press the Display/Menu/OK buttons or switch the Operating Mode Dial while a slide show is playing or it may interrupt the display and returns to the PLAY mode. To stop the slide slow, press the Menu button. LCD BRIGHTNESS: Changes the brightness setting (-5 ~ +5, Interval = 1) of the LCD display. The cursor returns to the CAPTURE menu automatically when the change is made. The setting is conserved even if the camera power is off. COPY TO CF CARD: Copy the captured images in the internal memory to the external CF card. Select the item by the arrow buttons ( / ) and then press the OK button to confirm. Press the OK button to confirm. SLIDE SHOW: Displays the captured images sequentially, with a user-defined delay between images (2, 4, 6, 8, 10). Select the item by the arrow buttons ( / ) and then press the OK button to confirm. Use the arrow buttons ( / ) DIGITAL ZOOM: In PLAY mode, you can press the OK button to gain 2X/4X digital zoom effect to get the details of the pictures taken. [. . . ] When the Self-Timer button is pressed, the 10-second self-timer is enabled. To disable the self-timer function, do any of the following: Press the Self-Timer button again. Change to another mode other than CAPTURE mode. Operating Mode Dial Switch the Operating Mode Dial to select the desired operating mode. There are five operating modes available as follows: CAPTURE: Capture/stores images PLAY: Review images in memory DELETE: Delete images in memory 23 Images Remaining/Image Number Indicator The digit number on the Status LCD may have different meanings in each mode: Capture Mode: Shows the number of the images that can be captured in your camera with current settings. [. . . ]