User manual PENTAX AUTO 110 LENSES

[. . . ] · When multiple accounts have been setup in Windows 2000 or Windows XP, log on with an account that has administrative rights before installing the software. 5 Macintosh Click [ACDSeeTM]. Follow the on-screen guidance and enter the registration information when the Setup screen appears. Reboot your PC after installation is finished (Other settings are not necessary during installation). Step 2 Installing the Software Installing the Image Processing Software (ACDSee for PENTAX) This section describes the procedures for installing ACDSee for PENTAX, which lets you view and edit images transferred to your Macintosh. 1 2 Turn your PC on. · If the PENTAX Software Installer screen does not appear Display the PENTAX Software Installer screen following the steps below. [. . . ] 3) Double-click [Setup. exe]. If QuickTime and DirectX are not installed in your PC, a message such as the one shown on the right appears when ACDSee for PENTAX 2. 0 is run. Click [Close] and install QuickTime and DirectX from the [PENTAX Software Installer] screen. 1 2 3 4 5 If QuickTime and DirectX are not installed in your PC, operation of ACDSee for PENTAX 2. 0 is not guaranteed. If your PC is running Windows Media Player earlier than version 7. 1, a message such as the one shown on the right may appear during installation. In this case, follow the instructions below to update Windows Media Player before installing the software. http://www. microsoft. com/windows/ie/default. mspx To guarantee more efficient operation, you are recommended to update Windows from the above website after updating Windows Media Player. Turn your Macintosh on. Double-click the [Master Installer] icon to display the PENTAX Software Installer screen. You can choose the languages from the displayed screen. 3 You can choose the languages from the displayed screen. Follow the on-screen guidance to input registration information and install the software. 4 Install QuickTime and DirectX. If QuickTime and DirectX are not installed in your PC, install them before installing ACDSee for PENTAX 2. 0. · If you connect the camera to a PC while the USB connection mode is set to [PictBridge], do the following operation according to your operating system. After completing the procedure, change the connection to [PC] and reconnect the camera and PC again. OS Windows XP Windows 2000 Windows Me MacOS 10. 3 MacOS 10. 2 MacOS 10. 1 Status for USB connection Recognized as PENTAX Optio S55, but cannot read images when trying to acquire them. Follow this instruction Turn off the camera and remove the USB cable from your PC. Click "Cancel", turn off the camera and remove the USB cable from your PC. Click "Cancel", turn off the camera and remove the USB cable from your PC. For Macintosh user go to Macintosh Step 4 3 Turn your camera on. If the Device Detector screen does not appear, display and copy the images following the steps in "When the Device Detector screen does not appear". When the camera is connected to a PC with the USB cable, the power indicator blinks to indicate that the camera is communicating with the PC. Disconnecting the Camera from Your PC Windows XP 1 2 Double-click the [Safely Remove Hardware] icon in the task bar. The Stop a Hardware device screen appears. The i-Photo function starts, but the image cannot Turn off the camera and remove the USB cable be identified. "Print error" is displayed on the camera's LCD monitor. Turn off the camera and remove the USB cable from your Macintosh computer. [. . . ] Turn off the camera and remove the USB cable from your Macintosh computer. Turn off the camera and remove the USB cable from your Macintosh computer. Transferring Images 4 Confirm that [Acquire images from the device with ACDSee] is checked and click [OK]. MacOS 9. 2 The message "Software needed for the USB device "Unnamed device" is not available. Would Click "Cancel", turn off the camera and remove you like to look for the software on the internet?" the USB cable from your Macintosh computer. appears on your Macintosh computer. 3 5 Click [Next]. Select [USB Mass Storage Device] and click [OK]. [. . . ]