User manual PENTAX 6X7 90MM F/2.8 LEAF SHUTTER LENS

[. . . ] Images taken with the purpose of obtaining copyrights also cannot be used outside the scope of use of the copyright as laid out in the Copyright Act, and care should be taken here also. Regarding trademarks PENTAX and Optio are trademarks of HOYA CORPORATION. PRINT Image Matching enabled digital still cameras, printers and software help photographers to produce images more faithful to their intentions. Some functions are not available on printers that are not PRINT Image Matching III compliant. [. . . ] Recorded Pixels Focusing Area Sensitivity EV Compensation Movie Digital Zoom MENU Cancel 10M 10M 7M 5M 3M 12 3 OK OK Taking Pictures 5 6 Press the 4 button. The setting is saved. Press the 3 button. The camera returns to capture status. · The number of recorded pixels for images captured in 9 (Green) mode is fixed at N. · The number of recorded pixels for images captured in C (Half-length Portrait) or J (Frame Composite) is fixed at h. · The number of recorded pixels for images captured in c (Digital SR) mode is fixed at f. Setting the Exposure (EV Compensation) You can adjust the overall brightness of the picture. Use this function to take pictures that are intentionally overexposed or underexposed. 1 2 Press the 3 button in A mode. The [A Rec. Mode] menu appears. Use the four-way controller (23) to select [EV Compensation]. 89 3 Use the four-way controller (45) to select the EV value. To brighten, select a positive (+) value. You can choose the EV setting in the range of ­2. 0 EV to +2. 0 EV in 1/3 EV steps. Rec. Mode 1/2 Recorded Pixels 10M Focusing Area Auto Sensitivity EV Compensation 0. 0 Movie Digital Zoom MENU Exit 4 3 Taking Pictures 90 Press the 3 button. The camera returns to capture status. The EV compensation function cannot be used in 9 (Green) or b (Auto Picture) mode. Saving the EV Compensation value setting 1p. 97 Setting the Sensitivity You can select the sensitivity to suit the brightness of the surroundings. Auto The sensitivity is automatically adjusted by the camera. (Sensitivity 100 - 800) 100 The lower the sensitivity, the less noise that affects the image. 400 800 1600 Higher sensitivity settings use faster shutter speeds in low light 3200 conditions to reduce camera shake, but the image may be affected by noise. 6400 1 2 3 Press the 3 button in A mode. The [A Rec. Mode] menu appears. Use the four-way controller (23) to select [Sensitivity]. Press the four-way controller (5). A pull-down menu appears. 4 Use the four-way controller (23) to change the sensitivity. Rec. Press the four-way controller (5). The [Movie] screen appears. Use the four-way controller (23) to select [Recorded Pixels]. Press the four-way controller (5). A pull-down menu appears. 3 Taking Pictures Use the four-way controller (23) to change the number of recorded pixels. Rec. Time 15:02:26 Recorded Pixels 12805 15 1 640 Movie SR 24 640 15 320 24 320 15 MENU Cancel OK OK 7 8 Press the 4 button. The setting is saved. Press the 3 button twice. The camera returns to capture status. 95 Setting the Movie SR (Movie Shake Reduction) Function In C (Movie) mode, you can compensate for camera shake while you are recording a movie with the Movie SR (Movie Shake Reduction) function. 1 3 Taking Pictures 96 Press the 3 button in A mode. The [A Rec. Mode] menu appears. 2 3 4 5 Use the four-way controller (23) to select [Movie]. Press the four-way controller (5). The [Movie] screen appears. Use the four-way controller (23) to select [Movie SR]. Use the four-way controller (45) to select O (On) or P (Off). The setting is saved. Movie Recorded Pixels Movie SR 640 24 MENU 6 Press the 3 button twice. The camera returns to capture status. The Movie SR function cannot be used when the recorded pixels is set to F (1280×720 pixels, 15fps). Saving the Settings (Memory) The Memory function is for saving the current camera settings when the camera is turned off. For some camera settings, the Memory function is always set to O (On) (the settings are saved when the camera is turned off), while for others you can choose on or off (to choose whether the settings are saved or not when the camera is turned off). The items which can be set to O (On) or P (Off) in the Memory function are shown in the table below. (Items not listed here are always saved in the selected settings when the camera is turned off. ) If you select O (On), the settings will be saved in the status they were in immediately before the camera was turned off. If you select P (Off), the settings will be reset to the defaults when the camera is turned off. The table below also shows whether the Memory default setting for each item is on or off. Default Page Setting Face Priority A Face Recognition mode set by using the I button. P p. 61 Flash Mode The flash mode set with the four-way controller (4) O p. 84 p. 78 Drive Mode The drive mode set with the four-way controller (2) P p. 79 Focus Mode The focus mode set with the four-way controller (5) P p. 86 Zoom Position The zoom position set with the Zoom/w/x button P p. 67 Sensitivity The [Sensitivity] setting on the [A Rec. Mode] menu P p. 90 EV The [EV Compensation] setting on the P p. 89 Compensation [A Rec. Mode] menu The [Digital Zoom] setting on the [A Rec. Mode] Digital Zoom O p. 69 menu The information display mode set with the DISPLAY P p. 18 4/W button If a new SD Memory Card is inserted when On has O -- File No. [. . . ] Phone: 303-799-8000 FAX: 303-790-1131 Declare under sole responsibility that the product identified herein complies with 47CFR Parts 2 and 15 of the FCC rules as a Class B digital device. Each product marketed is identical to the representative unit tested and found to be compliant with the standards. Records maintained continue to reflect the equipment being produced can be expected to be within the variation accepted, due to quantity production and testing on the statistical basis as required by 47CFR §2. 909. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. [. . . ]