User manual PEG PEREGO SWITCHABLE

[. . . ] Com manuals search engine + VIAGGIO 0 SWITCHABLE E N Instructions for use KO 사용지침 UNIVERSAL CATEGORY 0-13 Kg Group 0+ BELTED OK NO NO NO NO NO E N• "Viaggio 0+1 Switchable" is fastened to the vehicle in a rear-facing position using the vehicle’s seatbelt when used as a Group 0+ car seat (from 0 to 13 Kg). Com manuals search engine UNIVERSAL CATEGORY 9-18 Kg Group 1 BELTED OK NO NO NO NO NO E N• "Viaggio 0+1 Switchable" is fastened to the vehicle in a forward-facing position using the vehicle’s seatbelt when used as a Group 1 car seat (from 9 to 18 Kg). Com manuals search engine 9 10 A A B B 11 12 Downloaded from www. Com manuals search engine B C A C C 13 14 15 16 Downloaded from www. [. . . ] €¢ Do not use this car seat if more than seven years have elapsed from the date of production indicated on the structure; the natural aging of the materials may mean the car seat is no longer compliant with safety standards. €¢ Do not use accessories that have not been approved by the manufacturer or by the competent authorities. Instructions for use UNIVERSAL CATEGORY - Belted Group 1 Fastening with seatbelts 5• IMPORTANT: For the correct use of the “Viaggio 0+1 Switchable” car seat in Group 0+ mode, it is necessary to: - Extract from under the seat the casing that enables the car seat to be reclined. To extract it, press the handle and pull it towards you, extracting the base (arrows A and B). - Use the lever (arrow C) to recline the seat to its highest position. 2• “Viaggio 0+1 Switchable” car seat correctly installed to be used as a Group 0+ car seat. 3• Install the “Viaggio 0+1 Switchable” car seat on the vehicle’s seat so that it is rear-facing, as shown in the figure. Pass the vehicle seatbelt between the frame and body of the car seat following these steps: - slip the belt into the light blue belt guides first (arrow A); - fasten the belt, ensuring that it clicks into place (arrow B); 4• Pass the seatbelt through the upper light blue belt slot (arrow C). IMPORTANT: Take hold of the seatbelt and pull it firmly, so as to ensure that the “Viaggio 0+1 Switchable” fits as close as possible to the vehicle seat (arrow D). 1• 18 Instructions for use UNIVERSAL CATEGORY - Belted Group 0+ Fastening with seatbelts IMPORTANT: For the correct use of the “Viaggio 0+1 Switchable” car seat in Group 1 mode, it is necessary to: - Reposition the casing within the base of the car seat. 6• Install the “Viaggio 0+1 Switchable” car seat on the vehicle’s seat so that it is front-facing, as shown in the figure. 7• To make it easier to pass the vehicle’s seatbelts through the back of the car seat, it is necessary to recline the car seat to its lowest position by operating the lever, as shown in the figure. 8• Pass the vehicle seatbelt between the frame and body of the car seat. 9• The waist strap must pass through the lower guides, marked in red; fasten the belt, ensuring that it clicks into place. 10• Tighten the waist strap, ensuring it has passed through the lower guides, marked in red. 11• Bring the car seat back into the upright position by pulling the handle below the seat (Fig. 12• To complete the installation process, use the Steady Fix device: open the clip and pass the diagonal strap through it, ensuring that it is taut and not twisted (Fig. 13• IMPORTANT: Take hold of the seatbelt and pull it firmly upwards, so as to ensure that the “Viaggio 0+1 Switchable” fits as close as possible to the vehicle seat (Fig. Once installed, the car seat may be reclined to the desired position (See Point 6). How to secure your child in the “Viaggio 0+1 Switchable” car seat 1 4• Before placing the child in the car seat, release the Downloaded from www. Com manuals search engine harness by pushing the red button on the crotch strap buckle. 15• Lift the harness and attach the buckles to the elastic bands on the sides. [. . . ] How to replace the soft cover of the “Viaggio 0+1 Switchable” car seat To replace the soft cover of the “Viaggio 0+1 Switchable” car seat: 36• From below, slip the straps back in through the opening in the fabric (Fig. 39• Put the soft cover in place, starting at the seat and moving upwards, paying attention to the sides of the backrest. 40• Slip the soft cover over the headrest, ensuring the red tongue passes through the opening in the fabric. 41• Insert the straps through the soft cover, starting with the buckles. [. . . ]