User manual PEG PEREGO BOOK PLUS S

[. . . ] 5 FIXED OR SWIVELING FRONT WHEELS: Lift the levers to prevent the wheels from swiveling (fig_a) and lower them to allow the wheels to swivel (fig_b). 6 BRAKE: Press the lever down to apply the brake on the chassis and lift it to release the brake. 7 ADJUSTABLE HANDLEBAR: To adjust the height of the handlebar, press both of the side buttons at the same time (fig_a) and swing it into the desired position (fig_b), then release the buttons. 9 ATTACHING THE SEAT ONTO THE CHASSIS: the reversible seat can be attached onto the chassis to face mum or to face outwards (fig_a). [. . . ] 1 6 To adjust the height of the safety harnesses, release the two buckles on the rear of the backrest. Pull the shoulder straps towards you (arrow_a) until the buckles are released and insert them in the backrest loops (arrow_b). Remove the shoulder straps from the sack (arrow_c) and insert them in the most appropriate loop (arrow_d), then re-attach the two buckles on the rear of the backrest (arrow_e) The buckles are securely attached when a click is heard (fig_f). To open the hood, pull it towards you; to close the hood, push it backwards. The hood may only be used as a parasol if the backrest is not fully reclined. In this case, open the double slider zipper (fig_b) and unfasten the hood buttons on the rear of the backrest. The hood comes with a loop from which to dangle baby’s favorite toy (fig_c). 1 8 COVER: put on the cover, and fasten it underneath (fig_a) and on the sides of the footboard. For the baby carriage version, move the footboard up and place the cover over the front bar (fig_b), fastening it to the buttons of the hood (fig_c). For the stroller version, move the footboard down, insert the cover underneath the front bar (fig_d) and fix it in place. 19 BABY SAFE: pull the Baby Safe system out from under the leg rest (fig_a), attach it to the seat (fig_b), fit the front bar (fig_c), unbutton the fabric covering at the side and then attach the Baby Safe system to the sides of the armrests (fig_d). 2 0 RAIN CANOPY: position the rain canopy on the stroller (fig_a) and insert the two lateral loops over the hood buttons (fig_b). 2 1 Secure the rain canopy by attaching the elastic loop to the rear uprights (fig_a) or to the front uprights (fig_b), according to the seat position. 2 2 FOLDING UP: to fold up the seat press the outer sides towards the inside (fig_a) and fix in place with the fastener (fig_b). 2 3 FOLDING UP: The chassis can be folded up without the seat, with the seat facing the person pushing (recline the backrest before folding it) or with the seat facing forward. To fold the stroller, it is best to set the front wheels to their fixed position and close the hood (if fitted). Position the handlebar as shown in fig_a and lift the levers on the two uprights on the sides (fig_b). Pull the inner handle on the base (fig_c), keep hold of it, lift it (fig_d) and swing the handlebar forward until the chassis is folded. 2 4 Once the chassis is folded up, check that it has been secured with the clips on either side (fig_d) and fasten them if necessary. If necessary, it can be made even more compact by removing the rear wheels. [. . . ] CLEANING THE RAIN CANOPY: wash with a sponge and soapy water; do not use detergents. CLEANING FABRIC PARTS: brush fabric parts to remove dust and wash by hand at a maximum temperature of 30°C; do not wring; do not use chlorine bleach, do not iron; do not dry clean; do not apply solvent-based stain removers and do not dry in a tumble dryer. Peg Pérego can make changes at any time to the models described in this publication for technical or commercial reasons. PEG-PÉREGO AFTER-SALES SERVICE ACCESSORY If any parts of the item get lost or damaged, only use genuine Peg Pérego spare parts. [. . . ]