User manual PEAVEY XR 600B

[. . . ] For compliance with the Federal Noise Interference Standard, this equipment requires a shielded cable. This statement will be applied only for the printers marketed in U. S. A. Statement of The Canadian Department of Communications Radio Interference Regulations This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications. Le présent appareil numérique n'émet pas de bruits radioélectriques dépassant les limites applicables aux appareils numériques de la classe A prescrites dans le Règlement sur le brouillage radioélectrique édicté par le ministère des Communications du Canada. [. . . ] Tampering with this product may result in injury, fire, or electric shock. Not only should you not put your hand in the paper outlet slot while printing is in progress, never put your hand into the outlet even when printing is not in progress. However, since the cutter blade is on the inside of the printer cover, be careful not to place your face or hands too close to the cutter blade. 3 During and immediately after printing, the area around the print head is very hot. 3 Since working on the cutter may be dangerous, be sure to turn off the printer first. ­ ­ CAUTION 3 We recommend that you unplug the printer from the power outlet whenever you do not plan to use it for long periods. Because of this, you should locate the printer so that the power outlet it is plugged into is nearby and easy to access. 3 If the voltage shown on the label on the of your printer does not match the voltage for your area, contact your dealer immediately. 3 Make sure that the printer is turned off and unplugged from the AC outlet and that the computer is turned off before making connections. 3 Do not connect a telephone line into the peripheral drive connector. Also, for safety purposes, do not connect wiring to the external drive connector if there is a chance it may carry peripheral voltage. 3 Do not operate the cover open lever while pressing on the printer cover with your hand. ) Non recoverable error ErrorDescription Flash memory write error Thermistor failure error Power supply error CPU error RAM R/W error POWERlamp Off Off Off Off Off ERRORlamp Flashes (On: sec. / Off: sec. ) Flashes (On: 0. 5 sec. /Off: 0. 5 sec. ) Flashes (On: sec. / Off: sec. ) On On Buzzer None short beeps (0. + 0. 5 sec. ) None One long beep ( sec. ) None Note If a non-recoverable error occurs, turn the power OFF, wait at least 0 seconds, and turn the power back ON. If the non-recoverable error continues to be indicated, consult a dealer for repairs. ­ ­ 6-4. The device will enter the adjustment mode if your turn it on while pressing the FEED switch. () The Self Printing Mode is entered by releasing the FEED switch after the buzzer sounds once. (Refer to Section 6-4-. ) (Holding down for more seconds) () Adjusting the Dot Alignment Mode is entered by releasing the FEED switch after the buzzer sounds twice. (Refer to Section 6-4-. ) (Holding down for more seconds) () The Hexadecimal Dump Mode is entered by releasing the FEED switch after the buzzer sounds three times. (Refer to Section 6-4-. ) (Holding down for more seconds) (4) The Black Mark Sensor Alignment Mode is entered by releasing the FEED switch after the buzzer sounds four times. (Refer to Section 6-4-4. ) (Holding down for more seconds) (5) The Near End Sensor Adjustment Mode is entered by releasing the FEED switch after the buzzer sounds five times. (Refer to the separate Specifications Manual for details. ) (Holding down for more seconds) (6) The Memory Switch Manual Setting Mode is entered by releasing the FEED switch after the buzzer sounds six times. (Refer to the separate Specifications Manual for details. ) (Holding down for more seconds) () The Memory Switch Override Mode is entered by releasing the FEED switch after the buzzer sounds seven times. [. . . ] Space: Host enabled to receive Mark: Host disabled to receive Memory switch 4-5 = : Status of this signal is not checked. · In X-ON/X-OFF communication mode, status of this signal is not checked. Signal ground Not connected Indicates whether data receive from host is enabled or disabled. DTR/DSRCommunicationMode Space when receive is enabled. Printer status . [. . . ]