User manual PEAVEY XD 2

[. . . ] All Rights Reserved LP440/LP441 User's Guide P/N 59318201, Revision 1. 0 Disclaimer Every effort has been made to ensure that the information in this document is complete, accurate, and up-to-date. The manufacturer assumes no responsibility for the results of errors beyond its control. The manufacturer also cannot guarantee that changes in software and equipment made by other manufacturers and referred to in this guide will not affect the applicability of the information in it. Mention of software products manufactured by other companies does not necessarily constitute endorsement by the manufacturer . [. . . ] Push the dispenser unit forward so that it covers the red platen roller. 36 Operation and Configuration Turning the printer ON 1. When the STATUS LED (2) lights green, release the button Turning the printer OFF 1. When the STATUS LED (2) goes off, release the button. 37 Performing a Test Print Important!: Overall print quality is readable and sharp. Make sure the printer is running on AC or on a full battery during a test print. Users can perform test prints to evaluate the print quality and also diagnose problems. Press the POWER button (2) while pressing and holding down the FEED button (1). The printer powers up in the test mode. 38 3. Note: If any fault is detected, contact your Oki dealer or service center. Before asking for a repair, please read the Troubleshooting section of this manual. Press the POWER button to exit the Test Print Mode and turn the printer off. 39 Printing Printing using the RS-232C Interface 1. Locate the RS-232C interface port cover (1) and lift it up to expose the port. 2. Make sure that the arrow mark on the connector of the RS-232C cable matches with the arrow mark by the side of the printer's port. When printing is finished, pinch either the left or right corner of the printed roll of label(s) and tear it off in the direction of the arrow in the diagram below. Note: The number of sheets you can print is determined by the printer's mode (continuous or peel mode). When you are printing non-separate labels and you have torn the labels at a wrong place, stop the printing and follow the instructions on the next page to correct the print job. 46 Adjusting Printing for Non-Separate Labels When printing on a continuous label roll (non-separate), if you tear off a label at the wrong place, proceed as follows. Interrupt printing on the computer, or by pressing the PRINT key (1) to take the printer OFFLINE. When the feeding stops, tear off the label correctly by pulling the label in the direction of the arrow shown in the 47 diagram. Press the PRINT button to return to the on-line state (STATUS LED lights green). You can now resume the print job. 48 The Label Dispensing mode You can choose to dispense labels in Continuous Mode and Dispense Mode. Configuring Dispense mode Dispense Mode can be set to Auto Print or Manual Print, as described below. Type Auto Print Description Prints one label after receiving data and waits for peeling. After the label is peeled off, the printer automatically prints the next label. After the specified number of labels are printed, printing terminates. No printing occurs even when the PRINT key is pressed. Manual Print To switch between Auto or Manual Print for the Dispense Mode, set the DIP switches and then hold down the PRINT or FEED button when turning the printer ON. When setting the dispense mode, the STATUS LED blinks green, and turns into a steady green signal upon completion of setting. [. . . ] Replace the print head. Vertical streaking in printouts Slanted text characters Bluetooth/WLAN interface is faulty. Print head is faulty. 63 Error Indicators STATUS (LED) Light (Red) Blink (Red) every 2s Light (Red) Mode All modes Online Description Low battery Error in Bluetooth or WLAN card Program illegal error Flashromerror Head error Cause Battery charge level is low. Replace the head. After Power On Blink GreenÌ Red every 2s Online Head wiring is disconnected. Warning: Never connect or disconnect interface cables (or use a switch box) with power applied to either the printer or the host. This may cause damage to the interface circuitry and the damageis not covered by warranty. 64 Specifications Basic Specifications Attribute Description Printing system Head density Maximum print area Print speed Direct Thermal printing system 203 dpi (8 dots/mm) 1. 9 inches (48 mm) wide x 6. 3 inches (160 mm) pitch 4. 1 inches (103 mm) per sdecond max. [. . . ]