User manual PEAVEY STADIA II DATASHEET

[. . . ] Please address any comments on this publication to: Training & Publications Department Okidata, Division of Oki America, Inc. Each product contains information technology that accurately processes date and time data between the years 1999 and 2000. These products, when used in combination with products purchased from other manufacturers, whose products properly exchange date and time information, will accurately process the date and time. All future products are committed to meeting the same Year 2000 compliance. [. . . ] Press the SEL button to select the printer, then set the Top of Form using the procedure described for single-sheet paper on page 12. To change the Top of Form setting for a single page, deselect the printer (press SEL button) and press the LF button until you reach the Top of Form position you want to use. To change the Top of From setting for multiple pages of continuous-form paper, deselect the printer (press SEL button) and press the LF button to move to the new Top of Form position, then press and hold the SHIFT button while pressing the QUIET/TOF button. The printer retains this setting until you park the continuous-form paper or until you change the Top of Form again. Press the TEAR button (1) to advance continuous forms up to the tear position so you can easily tear off a printed sheet without wasting paper or readjusting the printer. To return the paper to the print position, press the TEAR button again. Note: The Tear feature can not be used when the optional pull tractor is installed. This feature automatically moves continuous-form paper up to the tear position after the selected amount of time. The paper will return to the initial printing position when the printer receives data. to activate it , hold the SHIFT button and press the SEL button to enter the Menu Mode (1). Press the LF button until the Rear Feed group appears (2), press the FF/LOAD button until Form Tear-Off appears (3), press the TEAR button (4) until the setting you want appears -- 500 ms, 1 sec, or 2 sec -- then hold the SHIFT button while pressing the SEL button to exit the Menu Mode (1). When your printer is in the Menu Mode, you can use the front panel buttons to change the defaults for the printer parameters. The changes you make in the Menu Mode are automatically saved in your printer's memory when you exit the Menu Mode and are retained even if you turn the printer of. To reset your printer to the factory defaults for the menu, turn the printer off, then press and hold the SEL and LF buttons while turning the printer back on again. If you have the printer in the Menu Mode and turn the printer off without first exiting, any changes you have made in the menu will be lost. To place your printer in the Menu Mode, hold the SHIFT button while pressing the SEL button. When you are done making changes in the Menu Mode, exit the mode (saving the changes you have made) by holding the SHIFT button while pressing the SEL button. Within each group is a list of items, each of which has various settings. The illustration at the right shows a printout of the factory settings for the menu. To generate a printout of the menu, hold the SHIFT button and press the SEL button to enter the Menu Mode, then press the PARK button. For a table showing the settings for each item within each group, see the Reference Section at the back of this manual. Active Buttons in Menu Mode 1 GROUP Button: Each time you press this button, the menu line that prints shows the next group. [. . . ] For information on parts not listed, please call our toll-free number 1-800-PEAVEYDATA or consult the dealer where you purchased your printer. Com - Order toll-free by phone at 1-800-PEAVEY-DATA (1-800-654-3282) using VISA, MasterCard, or America Express. 1 cpi 20 cpi Emulations: Interface: Graphics Resolution: Resident Fonts Letter Quality: Courier (10 cpi/12 cpi/proportional, with superscript/subscript) Letter Gothic (10 cpi/12 cpi/proportional, with superscript/subscript) Orator (10 cpi/12 cpi) Prestige (10 cpi/12 cpi) Roman (10 cpi/12 cpi; 18 point: 96 ASCII and foreign language characters) Swiss, Swiss Bold (10 cpi/12 cpi, with superscript/subscript; 18 point: 96 ASCII and foreign language characters) Utility: Bar Code: Buffer Size: Gothic (10 cpi/12 cpi, with superscript/subscript; proportional) Code 39, UPC A, UPC E, EAN 8, EAN 13, Interleaved 2 of 5, Code 128, Postnet 64K ML 590 80 cpl 96 cpl 120 cpl 137 cpl 160 cpl ML 591 136 cpl 163 cpl 204 cpl 233 cpl 272 cpl Characters Per Second (cps) 300 360 450 257 300 100 120 150 171 200 Impact dot matrix 24 pins, 0. 6000 hours at 25% duty cycle and 35% page density 15 minutes 200 million characters average in 10 cpi utility mode at 25% duty and black ribbon: 4 million characters color ribbon: black = 1. [. . . ]