User manual PEAVEY PV 10

[. . . ] Unplug this apparatus during lightning storms or when unused for long periods of time. Servicing is required when the apparatus has been damaged in any way, such as when power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. " Connect only to a power supply of the type marked on the unit adjacent to the power supply cord. If this product is to be mounted in an equipment rack, rear support should be provided. [. . . ] Fader The channel Fader is the channel output control, which sets the signal level to the left and right mix and the effects send control. CLIP 3 7 Tape In/Out 17 8 2 16 EFX SIGNAL 1 9 DEFEAT The tape input jacks are designed to accommodate tape, CD, 0 10 or computer sound card output levels. The output level is +4 HEADPHONE dBu for connecting to a recorder or sound card input. The tape inputs can be used as an additional stereo input by engaging the Tape/USB to Main Mix switch (27). The tape input can also be used to monitor the recorder/sound card output without the risk of feedback. If another device is connected to the Tape Input, this signal will be combined with the USB input signal. Medium Concert Hall Larger Concert Hall Darker Intimate Room Bright Larger Room Darker Bright Darker Large Space, Long and Darker Classic Spring Single Delay (Slap-back) Warm Delay with Repeats Dark Delay with Repeats Warm Delay Single Delay, 30-120 ms Warm Delay with Modulation Brightens and Adds Room Reverb Brightens and Adds Spring Reverb Green Signal LED and Red Clip LED The green Signal LED and red Clip LED are used to set the operating input level to the PVTM10, PVTM14, and PVTM20 effects processors. the signal level to the processor is affected by channel Fader , the Effects Send and the Effects Send Master Controls. Start with the Master Control (20) set to 0 (12 o'clock) and adjust the channel sends so that the signal LED lights and the clip LED blinks on occasionally, if at all. pressing the EFX defeat mutes the effects signal and lights the clip/mute LED. EFX Return Once the input level is set (see 17) use the EFX Return control to mix the effects processor output into the main left/right outputs. MON Send Master This is the master output level control for the monitor mix. The output level sent to the Monitor Send jack (37) is controlled by the channel Monitor Send controls (6) and by this master control. EFX Send Master This is the master output level control for the EFX mix. The output level sent to the EFX Send jack and the internal effects processor is controlled by the channel Fader (12), the channel EFX Send controls (7), and by this master control. To avoid damage to your hearing, make sure to turn the dial fully counterclockwise before using headphones. Slowly turn the knob clockwise until you reach a comfortable listening level. Power LED This LED indicates AC power is supplied to the unit, the power switch is on, and the unit is functioning properly. If phantom power is used, do not connect unbalanced dynamic microphones or other devices to the XLR inputs. Tape To CTRL/HP Depressing this switch adds the tape return to the Control Room (39) and Headphone Outputs (41) for zero latency monitoring. Tape/to Mix (Tape/USB to Mix) Depressing this switch routes the signal from the Tape Inputs (13) or USB Input (44) to the Left/Right Outputs (40). ) Contour Switch Engaging this switch enhances the signal by adding both bass and treble frequencies. [. . . ] If the product or component must be shipped to Peavey for warranty service, the consumer must pay initial shipping charges. If the repairs are covered by warranty, Peavey will pay the return shipping charges. How To Get Warranty Service (1) Take the defective item and your sales receipt or other proof of date of purchase to your Authorized Peavey Dealer or Authorized Peavey Service Center. Include a detailed description of the problem, together with a copy of your sales receipt or other proof of date of purchase as evidence of warranty coverage. [. . . ]