User manual PEAVEY HDH 3 DATASHEET

[. . . ] NOTE: FOR UK ONLY As the colors of the wires in the mains lead of this apparatus may not correspond with the colored markings identifying the terminals in your plug, proceed as follows: (1) The wire which is colored green and yellow must be connected to the terminal which is marked by the letter E, or by the earth symbol, or colored green or green and yellow. (2) The wire which is colored blue must be connected to the terminal which is marked with the letter N, or the color black. (3) The wire which is colored brown must be connected to the terminal which is marked with the letter L or color red. GROUND POLARITY SWITCH Three-position, rocker-type switch, which for most applications should be operated in the center (zero) position. [. . . ] If the amp repeatedly blows fuses, it should be taken to a qualified service center for repair. POWER/STATUS LED Located on front panel this LED illuminates green when the Power Switch is in the "ON" position and AC power is supplied. When DDT is defeated, the LED will illuminate red when clipping occurs. INPUT JACK This input will accept signals from all types of bass pickups. iNPUT PAD SWITCH Provided for instruments that have extremely high output , which can result in overdriving (distorting) the input stage. Pressing the switch to its "in" or "active" position reduces the level of the input signal by 10 dB. This jack is buffered off the input jack so it is just like plugging directly into the tuner. When the knob is fully counterclockwise (set to 0), there is no voicing added. The final level adjustment should be made after the desired sound has been achieved. LINE OUT--XLR JACK Provides low impedance, electronically balanced signal for patching into a sound reinforcement or recording console. LINE OUT LEVEL CONTROL Controls the output level of the balanced line out. Pad = out (Passive) Bright = out (Normal) Pre-Gain = 5 (12 o'clock) Contour = 0 (fully counterclockwise) Bass = 0 (12 o'clock) Mid = 0 (12 o'clock) Mid Shift = 0 (12 o'clock) High = 0 (12 o'clock) Master Volume = 10 (fully Clockwise) Line Out Level = 10 (fully Clockwise) Nominal input: 315 mV RMS Minimum input: 28 mV (pre gain and master fully CW) Maximum input: 9 V (maximum signal at input before clipping occurs) Bright boost: + 8 dB @ 5 kHz Contour: Special frequency compensation Bass: ± 15 dB @ 30 Hz, Shelving type Eq Mid : ± 15 dB @ 200 @ 2 kHz (Mid shift control determines center frequency) Mid Shift: 200 to 2 kHz High: ±15 dB @ 8 kHz, Shelving type Eq 82 V RMS) into 2 ohms with no more than 1% THD+N 308 watts (35. 63 V RMS) into 8 ohms with no more than 1% THD+N Level is dependent on level control setting and pre gain setting Typically greater than 102 dB below full power @ 8 ohms unweighted 315 V RMS) with pre @ 5, Master @ 10 Controlled via footswitch, ground tip to defeat. 61 dB, 100mW to 160 W RMS, 20 Hz to 20 kHz (8 ohm load, typically below 0. 450 Watts RMS with 2 Ohm load 300 Watts RMS with 4 Ohm load RD 170 Watts RMS with 8 Ohm load Set to appropriate level for instrument used NOTE: "DDT should be utilized for maximum speaker protection" Slap Setting In Set to appropriate level for instrument used Doesn't matter when Mid is set to 0 Set as necessary Set to appropriate level for instrument used What This Warranty Does Not Cover The Warranty does not cover: (1) damage caused by accident, misuse, abuse, improper installation or operation, rental, product modification or neglect; (2) damage occurring during shipment; (3) damage caused by repair or service performed by persons not authorized by Peavey; (4) products on which the serial number has been altered, defaced or removed; (5) products not purchased from an Authorized Peavey Dealer. Who This Warranty Protects This Warranty protects only the original retail purchaser of the product. Speakers, baskets, drivers, diaphragm replacement kits and passive crossovers) and all Accessories Tubes and Meters Duration 2 years *(+ 3 years) 2 years *(+ 1 year) 3 years *(+ 2 years) 1 year *(+ 1 year) 2 years 1 year 90 days [*denotes additional warranty period applicable if optional Warranty Registration Card is completed and returned to Peavey by original retail purchaser within 90 days of purchase. What Peavey Will Do We will repair or replace (at Peavey's discretion) products covered by warranty at no charge for labor or materials. If the product or component must be shipped to Peavey for warranty service, the consumer must pay initial shipping charges. If the repairs are covered by warranty, Peavey will pay the return shipping charges. How To Get Warranty Service (1) Take the defective item and your sales receipt or other proof of date of purchase to your Authorized Peavey Dealer or Authorized Peavey Service Center. Include a detailed description of the problem, together with a copy of your sales receipt or other proof of date of purchase as evidence of warranty coverage. [. . . ] Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. If you have any questions about this warranty or service received or if you need assistance in locating an Authorized Service Center, please contact the Peavey International Service Center at (601) 483-5365 / Peavey Canada Ltd. [. . . ]