User manual PEAVEY BANDIT 75

[. . . ] When set to lower settings, the power compression simulation will be much more pronounced. POWER LED (19) Illuminates when AC power is being supplied to the amp POWER SWITCH (20) Depress the switch to the "on" position. The red pilot light (LED) will illuminate indicating power is being supplied to the unit. BACK PANEL FEATURES GROUND SWITCH (21) Three position rocker-type switch, which, in most applications, should be operated in its center or zero position. [. . . ] There may be some situations when audible hum and/or noise will come from the loudspeaker. If this situation arises, position the ground switch to either positive or negative (+ or -) or until the noise is minimized. NOTE: Should the noise problem continue, consult your Authorized Peavey Dealer, the Peavey Factory, or a qualified service technician. LINE CORD-120 V products only (22) For your safety, we have incorporated a three-wire line (mains) cable with proper grounding facilities. If it is necessary to use the equipment without proper grounding facilities, suitable grounding adaptors should be used. Less noise and greatly reduced shock hazard exists when the unit is operated with properly grounded receptacles. When using remote footswitch, always insert the plug fully (second click) to insure proper operation. POWER AMP INPUT (25) Used to connect line level signal to the power amplifier. PREAMP OUT (26) The preamp out can be used to route the amplified signal to a mixing console, tape recorder, etc. connect the preamp output using a shielded cable to an input of the tape recorder , mixer , etc. Dynamics @ IO 80 W RMS into 8 ohms 100 W RMS into 4 ohms Power @ Clipping: (typically) (5% THD, 1 kHz, 120 V AC line) 80 W RMS into 8 ohms 100 W RMS into 4 ohms Frequency Response: +O, 3 dB, 60 Hz to 20 kHz, @ 65 W RMS into 8 ohms Hum & Noise: Greater than 86 dB below rated power Power Consumption: 300 W @I 50/60 Hz, 120 V AC, Domestic 300 W @ 60 Hz, 220-230/240 V AC, Export PREAMP SECTION The following specs are measured @ 1 kHz with the controls preset as folio ws: Push Bright, Off (Out) Channel Select Normal (Out) Low & High @ IO Mid @ 0 Presence @ 0 dB Pre 5: Post Gain @ IO Gain 6: Thrash, Off (Out) Normal Levels are with normal volume @ 5 Minimum Levels are with normal volume @ 10 3 V RMS or 0 dBV, 1 V RMS if Effects Level is in (Switching jack provides Effects Send to Effects Return connection when not used) Preamp Output: Load Impedance: 1 K ohm or greater Nominal Output Level: 0 dBV, 1 V RMS Power Amp Input: Impedance: High-Z, 30 K ohms Designed Input Level: 0 dBV, 1 V RMS (Switching jack provides preamp output to power amp input connection when not used) System Hum & Noise @ Nominal Input Level: (20 Hz to 20 kHz unweighted) 72 dB below rated power Equalization: Special low, mid, & high passive type EQ Presence: +6 dB @ 5 kHz Push Bright: +6 dB @ 2 kHz Push Thrash: -20 dB notch @ 1 kHz in Lead channel Push Gain: Increases Lead gain Push Resonance: +6 dB @ cabinet resonance External Footswitch Functions: Lead Channel Defeat (when selected with button) Effects Loop Bypass Dimensions & Weight: 20. There will be no identification card issued by Peavey Electronics Corporation. Completion and mailing of WARRANTY REGISTRATION CARDS - Should notification become necessary for any condition that may require correction, the REGISTRATION CARD will help ensure that you are contacted and properly notified. Notice of address changes - If you move from the address shown on the WARRANTY REGISTRATION CARD, you should notify Peavey of the change of address so as to facilitate your receipt of any bulletins or other forms of notification which may become necessary in connectron with any condition that may require dissemination of information or correctron. WARNING: When using electric products, basic cautions should always be followed, including the following. All safety and operating instructions should be retained for future reference. This product should be located so that its position does not interfere with its proper ventilation. wall or placed in a built-in enclosure that will impede the flow of cooling air. This product should not be placed near a source of heat such as a stove, radiator, or another heat producing amplifier. Connect only to a power supply of the type marked on the unit adjacent to the power supply cord. For more information on grounding, write for our free booklet "Shock 9. Periodically check cords for cuts or signs of stress, especially at the plug and the point where the cord exits the unit. [. . . ] For more information on grounding, write for our free booklet "Shock 9. Periodically check cords for cuts or signs of stress, especially at the plug and the point where the cord exits the unit. The power supply cord should be unplugged when the unit is to be unused for long periods of time. If this product is to be mounted in an equipment rack, rear support should be provided. [. . . ]