User manual PARROT MKI9000

[. . . ] 5 Installing the kits power cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Installing the audio connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Installing the individual components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Installing the double microphone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Several set-ups are therefore possible depending on the type of car stereo and your vehicle. If your car stereo is not fitted with ISO connectors, you need to purchase an ISO adapter cable to simplify the wiring procedure. Refer to the range of ISO adapters on our website. Caution Unplug the battery before installing the kits power cable. Before you install the individual components, check that the installation locations have been selected in such a way that the cable length is sufficient to connect every element. Do not install any component (remote control, microphone. . . ) in the airbag deployment area. Once the installation is complete, make sure that no cables are pinched or trapped. Removing the car stereo Remove your car stereo from you vehicle. Refer to your car stereo user guide or contact your car dealer for more information. Remove the audio system from your vehicles dashboard to access the wiring harness. The mute function is used to cut the sound of your car stereo to enable a phone call. The choice of the mute-in jack depends on your car stereos configuration. 3 Installing the kit Note : If you have the possibility to use a multimeter, test and verify all connections on the vehicle before connecting the Parrot MKi9200 wiring loom. Car stereo with ISO connectors 1. Join the vehicles audio and power supply cables to the female connectors of the Parrot MKi9000. On the installation cable, connect the free yellow wire to one of the audio systems corresponding mute-in jacks if available (mute in 1, mute in 2 or mute in 3). Note : Mute in 1, mute in 2 and mute in 3 are only suggested mute locations. You first have to test and verify the mute on the vehicle. 4 Car stereo with line-in Use this type of connection by wiring the line-out (brown & white wire or red & black wire) to your car stereos line-in. Using the two pairs of line-out will enable you to take advantage of the music function in stereo over your vehicles speakers. On the installation cable, connect the free yellow wire to the corresponding audio systems mute-input if available (mute in 1, mute in 2 or mute in 3). Installing the electronic box Avoid installing the electronic box near heating or air-conditioning system, on a spot directly exposed to sunlight or behind metal walls. Make sure the electronic box stays fixed once it is installed and that it will not move while you are driving. If you are short of space behind the car stereo to install the electronic box, consider installing it in the glove box. 5 Installing the kits power cable Refer to your car stereos wiring diagram. The red wire of the kits cable must correspond to the constant +12V supply, the orange wire to the ignition +12V and the black wire to ground. Check that the orange wire is not connected to the constant +12V supply, as you could run down the vehicles battery. Note : On some vehicles, there is no ignition +12V on the vehicle's connectors. You must therefore connect the orange power supply wire to the fuse box or another ignition power source. Installing the audio connectors Installing the music cable Connect the music cable to the electronic box and place the USB / iPod / Jack connectors into the glove box, the central console or the parcel tray depending on the configuration of your dashboard. Note : Use the provided protection cap to protect the connectors. Installing the music cable grommet system The music cable grommet system allows you to adjust the cable length while reducing its wear. Drill a 20 mm hole in your dashboard (glove compartment or parcel tray). > You can now connect your music cable to the bluebox. 6 Installing the individual components Installing the double microphone Selecting a location In order to get hi-quality conversations, we advise you to respect the following recommendations: Make sure the microphone is installed as close to the mouth of the user as possible. [. . . ] Press the jog wheel and select USB. Using the Parrot MKi9000 with an audio player connected via Bluetooth Compatibility You can use the Parrot MKi9000 to listen to songs stored on your mobile phone / PDA / smartphone. Your mobile phone must support the Bluetooth® A2DP profile (Advanced Audio Distribution Profile). Playing a music file If you are using a Bluetooth audio player for the 1st time, you have to pair both devices. Start playing a song on your audio player. Note : Volume for calls and for streaming audio work separately. Using the Parrot MKi9000 with an analogue audio player 1. Connect your audio player to the Parrot MKi9000 using the Jack connector. [. . . ]