User manual PARKSIDE XQ2

[. . . ] Page Page Page Page Page 6 6 6 6 6 Safety Safety advice relating to this specific tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 6 Operation Switching on and off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Vacuum dust extraction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Attaching / detaching sanding sheets. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] J ave repairs carried out only by an electrician or H the relevant service centre. J o not operate the device if it is damp and do not D use it in a damp environment. J f you use the device outdoors, always connect I it through a residual current device with a maximum trip current of 30 mA. J f using an extension lead always use one that is I approved for outdoor use. J lways work with the mains lead Q leading A away from the rear of the device. To avoid the danger of injury, burning and damage to health: mDanger of fire from flying sparks!Be aware that persons operating the W tool or in its vicinity may be at risk of being in contact with or inhaling dusts. Working with this tool can give rise to dusts that may be hazardous to health, inflammable or explosive. Harmful or poisonous dusts can, for example, arise from sanding paints containing lead, or from certain types of hardwoods or metals. Wear a breathing mask and use a suitable dust / chip vacuum extraction device. J hen sanding wood and in particular when W working on materials that give rise to dusts that are hazardous to health, the sander must be connected to a suitable external dust extraction device. J Wear protective glasses, hearing protection, dust protection masks and protective gloves. J nsure that there is adequate ventilation when E working on plastic, paint, varnish etc. J void sanding paints containing lead or other A substances hazardous to health. J irmly support the workpiece (in a clamp or vice) F unless its own weight is enough to keep it in place. J o not abrade moistened materials or damp D surfaces. Proper procedure and handling: J ever use the tool for a purpose for which it was N not intended nor with non-original parts / accessories. J lways switch on the device before placing it A against the workpiece. After abrading, lift the device from the workpiece before switching it off. J llow the device to come to a complete standstill A and switch it off before you put it down. J hen taking a break from your work, before W carrying out any tasks on the device itself (e. g. changing the sanding belt) and when you are not using the device, always pull the mains plug out of the mains socket. Do not use the device if you cannot concentrate or you are feeling unwell. L Operation L Switching on and off Caution! [. . . ] L Declaration of conformity / L Maintenance and cleaning Attention: before starting any work on your sander, always pull the plug out of the mains socket. j emove any dirt from the tool, surfaces and R other items in the working area immediately after you finish work. j lean the safety filter Y of the dust extraction C box T by pulling the safety filter out of the dust extraction box T. Suck out the debris carefully with a vacuum cleaner using a low suction pressure. [. . . ]