User manual PARKSIDE PEBS 900 SE

[. . . ] pebS 900 Se BELTSANDER OperationandSafetyNotes 6 Beforereading, unfoldthepagecontainingtheillustrationsandfamiliariseyourselfwithallfunctionsofthe device. GB/IE/CY OperationandSafetyNotes Page 5 7 8 1 2 3 4 16 12 15 13 14 6 5 14 a 9 b 6 C 10 11 D e F Table of contents Introduction Proper use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page Features and equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page Included items . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page Technical information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 6 6 7 7 7 8 8 8 9 General safety advice for electrical power tools 1. Workplace safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 2. Electrical safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Page 3. [. . . ] By using the right electrical power tool for the job you will work more safely and achieve a better result. 3. Personal safety a) remain alert at all times, watch what you are doing and always proceed with caution. Do not use the device if you are tired or under the influence of 8 GB/IE/CY General safety advice for electrical power tools b) Do not use an electrical power tool if its switch is defective. An electrical power tool that can no longer be switched on and off is dangerous and must be repaired. c) Pull the mains plug from the socket before you make any adjustments to the device, change accessories or when the device is put away. This precaution is intended to prevent you from unintentionally starting the device. d) When not in use always ensure that electrical power tools are kept out of reach of children. Do not let anyone use the device if he or she is not familiar with it or has not read the instructions and advice. Electrical power tools are dangerous when they are used by inexperienced people. Check for any parts that are broken or damaged enough to detrimentally affect the functioning of the device. Many accidents have their origins in poorly maintained electrical power tools. Carefully maintained cutting tools with sharp cutting edges are less likely to jam and are easier to control. in accordance with these instructions and advice, and the stipulations drawn up for this particular type of device. In doing this, take into account the working conditions and the task in hand. J When taking a break from your work, before carrying out any tasks on the device itself (e. g. changing the sanding belt) and when you are not using the device, always pull the mains plug out of the mains socket. Q Q duce good sanding results. By adopting this approach you will also prolong the life of your sanding belts and obtain a smoother workpiece surface. Sanding and surfaces: The sanding output and the quality of the surface finish obtained are determined by the belt speed and the grade of grit on the sanding belt (see the section on "Selecting the correct rotational speed and sanding belt"). Sanding procedure: j With the sander switched on, bring it into contact with the workpiece and move it forward carefully. Always work in the direction of the grain to avoid undesirable transverse sanding marks. After sanding always lift the device from the workpiece before switching it off. Q Preparing for use Tensioning / changing the sanding belt WarNING!Before you carry out any work on the belt sander always pull the plug out of the mains socket. [. . . ] E): j Place the belt sander on to the mounting frame 12 and guide the dust extraction spout 5 through the opening of the mounting frame 12 . j Place the two clamp plates 13 on to the holes provided on the opposite side and screw the clamp plates tight with the provided screws. j Insert the pins of the screw clamps 14 into the holes on one of the long sides of the mounting frame 12 (see Fig. Attach the mounting frame 12 by tightening the screw clamps 14 . 14 into the holes on one of the short sides of the mounting frame 12 . [. . . ]