User manual PARKSIDE PEBS 900

[. . . ] The manufacturer will not accept liability for loss or damage arising from improper use. L Q W E R T Y U I O P { 6 Technical information Parkside PEBS 900 230 V ~ 50 Hz 900 W 180 - 340 m / min n0 345 - 645 min-1 75 x 533 mm II / & 3. 8 kg Belt sander: Nominal voltage: Nom. power input: No-load belt speed: No-load speed: Sanding belt Protection class: Weight: Features and equipment Belt speed adjuster wheel Locking knob ON / OFF switch Toothed belt cover Dust extraction spout Belt adjuster screw Auxiliary handle Ventilation slots Tensioning lever Dust collection box Extraction adapter GB/IE Noise / vibration information Sound pressure level*: 87 dB (A) Sound power level*: Lw = 100 dB (pw) Hand-arm vibration*: < 2. 5 m / s2 Wear hearing protection! * Values determined in accordance with EN 60 745 The PEBS 900 belt sander has full-wave electronics with additional control electronics, soft start with inrush current limiting. Safety L Safety J When undertaking prolonged sanding of wood, and in particular when working on materials that give rise to dusts that are hazardous to health, the sander must be connected to a suitable external dust extraction device. Wear protective glasses, hearing protection, dust protection mask and protective gloves. [. . . ] Always work with the mains lead leading away from the rear of the device. To avoid danger to life and injury: J Danger of fire from flying sparks!For this reason, always make sure that nobody is placed in any danger and that there are no inflammable materials near the working area. J J J J J J J J J J J J J J J J J J J J J J J Safety / Preparing for first use J or grease. Do not use the device if you cannot concentrate or you are feeling unwell. L Advice on use L Preparing for first use Take note of the mains voltage. The mains voltage at the mains socket must match that shown on the rating plate on the device. L Light sanding pressure is enough j Apply light sanding pressure only. The weight of the belt sander alone is adequate to produce good sanding results. By adopting this approach you will also prolong the life of your sanding belts and obtain a smoother workpiece surface. Sanding and surfaces The sanding output and the quality of the surface finish obtained are determined by the belt speed and the grade of grit on the sanding belt (see the section on "Selecting the correct rotational speed and sanding belt"). The following basic rule applies: the higher the rotational speed / belt speed, the higher the sanding output and the finer the sanded surface finish. Sanding procedure With the sander switched on, bring it into contact with the workpiece and move it forward carefully. Always work in the direction of the grain to avoid undesirable transverse sanding marks. j The auxiliary handle U can be adjusted or removed to allow you to sand difficult-toreach places. Tensioning / changing the sanding belt m Attention: Before you carry out any work on the belt sander always pull the plug out of the mains socket. 1) Then release the tensioner for the sanding belt by moving the tensioning lever O fully outwards (see fig. 2) Next insert a new sanding belt or change the belt for one suitable for a different material or one with a different grit size. Important: The direction of the arrows on the inside of the sanding belt must agree with that on sander housing. Adjusting the sanding belt j Pick up the device, switch it on and turn it over. Adjust the belt tracking by turning the adjuster screw Y until the edge of the sanding belt is flush with and runs parallel to the edge of the device (Fig. m Attention: Always make sure that the sanding belt does not cut into the housing. Check the sanding belt regularly and if necessary re-adjust it using the adjuster screw Y. L Vacuum dust extraction m Warning!There is the danger of fire when working with electrical devices that have a dustbox or can be connected to a vacuum cleaner. [. . . ] We reserve the right to make technical modifications in the course of further development. L Maintenance and cleaning The belt sander is designed to be maintenance-free. m ttention: Before you carry out any work on A the belt sander always pull the plug out of the mains socket. Use a dry cloth to clean the device - never use petrol, solvents or cleaners that attack plastic. Remove any adhering dust with a narrow paint brush. Disposal / Information L Disposal The packaging consists of environmentallyfriendly materials. [. . . ]