User manual PARKSIDE PDKS 120

[. . . ] The manufacturer accepts no responsibility for damage(s) resulting from improper usage. 1 2 3 4 5 6 6a 7 8 9 10 10a 10b 10c 11 12 13 14 Q Included items Scroll saw PDKS 120 Blade guard Knurled nuts Plain washers 1x 1x 2x 2x 6 GB/IE/CY Introduction / Safety advice 2x 2x 10 x 1x 3x Guide plates Screws Saw blades Dust blow tube Threaded feet with nut, washer and retaining ring 1 x Allen key 1 x Operating instructions J J J Do not use electrical power tools in moist or wet surroundings. Ensure that your working area is well lit. Do not use electrical power tools in areas where there is risk of fire or explosion. Avoid touching earthed objects such as pipes, heating radiators, ovens or refrigerators with parts of your body. Do not allow other people, in particular children, to touch the electrical power tool or the mains lead. [. . . ] Damaged safety equipment and components must be properly repaired or replaced at a competent electrical equipment repair centre unless otherwise indicated in the operating instructions. Never use an electrical power tool that cannot be switched on and off properly. The use of inserted tools and accessories other than those recommended by the manufacturer could lead to you being injured. Have your electrical power tool repaired at an electrical equipment repair specialist. This electrical power tool complies with the relevant safety regulations. Repairs may only be carried out by a specialist electrical repair centre using original spare parts, otherwise injury could occur to the user. J 17. Safety advice relating specifically to scroll saws J Ensure that the scroll saw stands on a level, J Do not touch the mains lead if it becomes damaged or cut through while you are using the device. Pull the plug out of the mains socket immediately and have the device repaired by a horizontal surface. J 18. 8 Safety advice / Assembly suitably qualified person or at the Customer Service Centre. Always work with the mains lead leading away from the rear of the device. If a dangerous situation arises, pull the mains plug immediately out of the mains socket. Always switch on the electrical power tool before moving the workpiece against it. Do not cut moist materials or damp surfaces, Use only undamaged, defect-free saw blades 7 . Ensure that the teeth on the saw blade 7 point downwards before you mount it in the device. Before sawing, check the workpiece for foreign bodies such as nails etc. Injury and / or damage to property may result from the saw blade striking nails etc. Switch off the device before you remove any wood residue from around the saw blade. Any noxious dusts or vapours generated from sawing represent a risk to the health of the person operating the device and to anyone near the work area. Wear protective glasses, hearing protection, dust protection masks and protective gloves. J Hold the workpiece firmly on the table with J J J J J J J J both hands and push it slowly towards the saw blade. J Avoid making any sharp changes in direction during sawing to prevent the saw blade from twisting or tearing. J Before starting the saw cut, drill a hole at a corner or internal cut-out in the workpiece and start sawing from the hole. C) opening provided for it. 1 j Screw the dust blow tube 1 clockwise into the Intricate fretsaw work Q Bringing into use Q Take note of the mains voltage. The mains voltage at the mains socket must match that shown on the rating plate on the device. Make sure that the device is switched off before you connect it to the mains supply. [. . . ] If this product has been subjected to improper or inappropriate handling, abuse, or interventions not carried out by one of our authorised sales and service outlets, the warranty will be considered void. GB DES Ltd Units 14-15 Bilston Industrial Estate Oxford Street Bilston (Great Britain) WV14 7EG Tel. : 0870 / 787-6177 Fax: 0870 / 787-6168 e-mail: support. uk@kompernass. com The device requires almost no maintenance. Q Cleaning this immediately after you have finished using it. Use a dry cloth to clean the device. j Clean the device frequently; for best results, do j Do not allow any liquids to enter the device. j Keep the ventilation slots free of dust and dirt. Have your device repaired at the service centre or by qualified specialist personnel using original manufacturer parts only. [. . . ]