User manual PARKSIDE KH 3145 ELECTRIC TACKER

[. . . ] Page 7 Operation Loading the magazine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Setting the impact force. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Switching on and off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Stapling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Determine for yourself by practical tests the best staple or nail type and the optimum impact force setting for your substrate. Introduction / Safety Length (mm) Recommended impact force setting for: Hardwood (e. g. oak or beech) Staple / nail type 11, 4 mm L 10 mm Softwood (e. g. wood core plywood) 12 14 18 5-6 6 6-7 1-4 2-5 4-6 4-6 5-6 6-7 5-6 6 6-7 Type 53 6 mm L 4 mm Type 55 12 14 16 18 19 5-6 5-6 6-7 7 7 3-5 3-5 5 5 6 2-5 3-5 4-5 4-6 5-7 2-5 3-5 4-5 4-6 5-7 L 23 7 6 6-7 6-7 Type 47 L Safety Specific safety advice for this tool J nsure that the tool is always used in accordE ance with the operating instructions and only by persons over 18 years of age. Store the tool indoors in an enclosed, dry place where it cannot be reached by children. J J J J To avoid danger to life from electric shock: requently check the condition of F the tool, mains lead and plug. Always have any repairs carried out or replacement parts fitted at the service centre or by an electrical equipment repair specialist. J J A damaged tool, mains lead or plug presents a serious danger to life from electric shock. C heck before connecting the tool to the mains that the electricity supply circuit is 230 V ~ 50 Hz and is fitted with a max. D isconnect the mains lead from the mains supply O in the event of malfunction, fault rectification, maintenance or cleaning. Have repairs to the mains lead carried out only by an electrician or at the relevant service centre. A lways guide the mains lead O away from behind the hand grip Q to the rear of the tool. To avoid the risk of injury! J nsure that staples and nails cannot strike E people or animals. GB / IE 7 Safety / Operation rotect your eyes. This also applies to people who may be helping with the work by supporting or holding the workpiece. J efore you start to use the tool, check that it is B in perfect condition. J ake sure the tool is switched off before you M load the magazine T. S j ou can set the impact force at any value beY tween "1" (lowest impact force) and "7" (highest impact force) using the impact force controller Y. L To work safely! Switching on and off J efore undertaking any type of work with the tacker B make sure that materials and workpieces are safely held in position. If necessary have a second person on hand to support or hold the items steady. J f you have finished using the tool or are taking I a prolonged break from your work disconnect the mains lead O from the mains. m Attention!To switch on j et the On / off switch I to position "1" (see Fig. S To switch off j et the On / off switch I to position "O". S m Blow count: The Electric Tacker PET 23 VARIO is designed for 30 blows per minute. m Continuous Operating Time: The Electric Tacker PET 23 VARIO is designed for 15 minutes of continuous operation at the maximum blow count. L L Operation L Loading the magazine Use only fine wire staples (type 53), narrow-backed staples (type 55) or nails (type 47) ! [. . . ] Contact the service centre (see guarantee documentation). L Maintenance and cleaning m Attention!J efore carrying out maintenance or cleaning B disconnect the mains lead O from the mains supply. j lean the tool frequently, ideally after each use C using a dry, fluff-free cloth. Never use water or cleaning agent. Tool storage j f you are not going to use the tool for a while I disconnect the mains lead O from the mains. [. . . ]