User manual PARKINSON COWAN CALAST50AL

[. . . ] The installation instructions at the back of this book, on page 22, tell you how and where it can be fitted. If the cooker is already installed you must make sure that all instructions have been followed. If you are in any doubt ask a registered person. We have included several drawings to show the right and wrong way of doing things. The right way will have a smiling face by it. A sad face shows something is wrong. Do not remove the rating plate from the cooker as this may invalidate the guarantee. 2 Contents Lighting the cooker The grill The hotplate The oven Oven cooking chart Slow cooking Care and cleaning Installing the cooker General information What is wrong and why?Servicing Installation Instructions Technical data Safety requirements/ventilation Location of appliance/installation Testing Page 4 7 9 12 14 17 19 22 24 26 27 28 29 30 31 33 3 Contents CALOR SIG 305 Lighting the cooker CALOR SIG 305 Lighting the cooker The ignition system works by means of a battery. [. . . ] Please note: If we recommend you use hot soapy water we mean hot water with washing up liquid in it and not any other cleaning product. If you own a dishwasher please read the operating instructions for the machine before you wash any part of your cooker. Clean your cooker regularly using a cloth that has been wrung out in hot soapy water. When you remove parts of your cooker for cleaning do not plunge them into water whilst they are very hot as this may damage the finish of the parts. Cleaning the brass plated handles If your appliance is fitted with brass plated handles it is strongly recommended that only hot soapy water is used for cleaning. Any other cleaning materials will dull the brass plated finish. The hotplate Clean the hotplate top using a mild abrasive such as 'Jif'. You can remove the pan supports, burner caps and burner crowns to clean them. If any food spills during cooking you can place the pan on another burner to finish cooking. Then you can remove the dirty parts and clean them before the spill 'burns on'. 19 Care and cleaning CALOR SIG 305 Care and cleaning CALOR SIG 305 You can wash the removable parts in very hot soapy water. Make sure that the electrode and the hole and slots in the crown are not blocked with food or cleaning materials. You can remove any stubborn stains by scouring with a soap filled pad such as 'Brillo'. Don't let items which can catch fire or electric mains leads such as kettle flexes trail over any part of the cooker. Moving your cooker You may damage some soft or badly fitted floor coverings when you move the cooker. The floor covering under the cooker should be securely fixed so it does not ruck up when you move the cooker across it. Raise the cooker off its front feet by lifting it from inside the grill. When you replace the cooker push it back to the stop and make sure there is the same gap at each rear corner. The battery The battery for the ignition will usually last for many months. If the ignition system doesn't work you probably need to replace the battery. The battery is at the base of the cooker on the left-hand side of the front. When you need to replace the battery, open the main oven door, lift up the battery holder lid and replace the battery as shown in the diagram. When you fit the new battery, make sure the positive end (marked with a + sign) is next to the (+) sign on the battery holder. You can light the burners with a match until you have time to change the battery. 24 For your safety Do not try to disconnect the cooker from the gas supply if the supply pipe does not have a bayonet connection, as described in the installation instruction. If this is the case contact the person who installed the cooker. Reversing the oven door You can turn the oven door around so that it opens on the other side. [. . . ] CONNECTING TO GAS This appliance is designed to be installed with an appliance flexible connection only. Connection is made to the Rc½ (½" B. S. P. ) female threaded entry pipe located just below the hotplate level on the rear left hand side of the appliance. NOTE: ONLY LIQUID SEALANTS TO BE USED WHEN INLET GAS PIPE IS FITTED I. E. : DO NOT USE P. T. F. E. Check for gas soundness after connecting the gas supply. 32 CALOR SIG 305 The gas bayonet connector must be fitted in the shaded area indicated in Fig. [. . . ]