User manual PARASOUND ZAMP
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual PARASOUND ZAMP. We hope that this PARASOUND ZAMP user guide will be useful to you.
Manual abstract: user guide PARASOUND ZAMP
Detailed instructions for use are in the User's Guide.
[. . . ] Retain Instructions -- Retain safety and operating instructions for future reference. Heed Warnings -- Adhere to all warnings on the product and in the operating instructions. Attachments -- Do not use attachments not recommended by the product manufacturer; they may cause hazards. Accessories -- Do not place this product on an unstable cart or stand. [. . . ] Wall or Ceiling Mounting -- Mount the product to a wall or ceiling only as recommended. Heat -- The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat
11.
12. 21.
-2-
Zamp Front and Rear Panel Drawings
Zamp/Zone Amplifier
AC Present
Auto On
Power Switch
Headphone Jack
AC Present Auto On Indicator Indicator
Zamp Front Panel
Fuse Holder
Zamp/Zone Amplifier L R Stereo R Mono Bridge
CAUTION
RISK OF ELECTRIC SHOCK DO NOT OPEN
Level L
5-12V DC Trigger +
+
+
Input
120 Vac/60 Hz 120 W
Parasound Products, Inc. San Francisco, CA USA
R
L
Power Consumption: 120W 120V 60Hz AC
Bridge Switch
Input Jacks
Level Controls
DC Trigger
5-Way Binding Posts
AC Receptacle
Zamp Rear Panel
-3-
Making Connections to your ZAMP
Refer to Drawing on Page 3
When making connections, make sure there is no strain or tension on input leads or speaker wires that could cause them to pull loose. AC Line Connection Before you attach the AC cord, make sure the ZAMP power switch is in its off position. We recommend that you use only this cord and try to make direct connection to the AC wall outlet. Input Connections Use the right and left channel RCA jacks for stereo operation. For bridged mono operation, use only the right channel input jack and leave the left channel jack disconnected. Speaker Connections -- General Recommendations You may use 4 - 8 rated speakers for stereo operation. We do not recommend lower impedance loads, because they may cause overheating and activate one of the protection circuits. The speaker terminals of the ZAMP will accept 1/4" spade lugs, dual or single-banana plugs or bare wire up to 12 AWG. For best results you should never use speaker wire thinner than 16 AWG. If you use bare wire without plugs, make sure you strip off only enough insulation so the bared wire fits through the hole that runs sideways through the terminal's metal shaft. Before inserting the wire, twist all its strands tightly to prevent strays that could cause a short circuit between + and - terminals. You may want to "tin" the stripped wire with solder to prevent it from fraying. One side of the speaker wire will have some sort of mark such as printing, a raised ridge on the insulation or a different color conductor. This lets you know which wire to connect to the + and which to the - speaker terminals so you can make the same connections to the 5 way binding posts on the Zamp. Mono Bridge Switch Set the bridge switch to normal Stereo (up) or Mono Bridged (down) operation as marked on the rear panel. Make sure the power is off to the ZAMP before changing this switch position. If you accidentally leave the Mono Bridge switch in the Mono position for normal stereo listening, you will find stereo output will be very weak and distorted. Bridged Mono Operation When mono bridging your Zamp, do not connect a speaker with an impedance lower than 8 because in the bridged mode, each channel effectively "sees" only half of the speaker's actual impedance. For a 4 speaker, the impedance would be 2 per channel which is too demanding on the amplifier. [. . . ] Fingerprints may be removed with a soft cloth moistened with clean water or window cleaner. In Case of Trouble If you suspect a problem with this unit, contact your authorized Parasound Dealer or Installer, or call Parasound Technical Services. We may be able to suggest diagnostic tests you can easily perform that may save you a lot of trouble. If we determine that your ZAMP should be returned to Parasound or an Authorized Warranty Center for inspection and possible servicing, call for the location of a Warranty Center near you. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE PARASOUND ZAMP
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual PARASOUND ZAMP will begin.