User manual PANASONIC TY-EW3D2ME

[. . . ] Viewing 3D Content Do not use the 3D Eyewear if you have a history of over-sensitivity to light, heart problems, or have any other existing medical conditions. Stop using the 3D Eyewear immediately if you feel tired, discomfort, or any other uncomfortable sensation. Take a break of between 30 - 60 minutes after viewing 3D content on interactive devices such as 3D games or computers. [. . . ] If the eyewear stops receiving infra-red signal from the television, the power automatically switches off after 5 minutes. Liquid Crystal Shutter (lens) Controls the images for 3D viewing. The left and right liquid crystal shutters are alternately opened and closed in time with the left side and right side images that are alternately displayed on the television to achieve the 3D effect. Charging port Power switch (bottom side of 3D Eyewear) Connect the charging cable. The 3D Eyewear is turned on by setting the power switch to "ON". Set the power switch to "OFF" to turn off the 3D Eyewear. Indicator lamp Lights or flashes during use or charging to show the status of the rechargeable battery. Battery status shown by indicator lamp Power/indicator lamp status Lights for 2 seconds when turned on Flashes 5 times when turned on Flashes once every 2 seconds when in use Lights continuously when off Lamp off Battery status Sufficient battery level Low battery level Operating normally Charging Power off 6 - ENGLISH Accessories < > indicates the quantity. 3D Eyewear case ·······················<1> Charging cable ···························<1> Ferrite core·································<1> Attaching Ferrite Core Be sure to attach the provided ferrite core to the charging cable to reduce interference or electrical noise. Attach the ferrite core as close to USB connector of the charging cable as shown. Close the ferrite core until it clicks. Mini USB connector USB connector ENGLISH - 7 Viewing 3D Images NOTE · Charge the 3D Eyewear before using the first time after purchase or after long periods of disuse. Using the television menu controls, set so that 3D images are shown. 1. (When 3D image signals are being received) press the MENU button on the television remote control. Select "Picture Display", and use to select "3D" or "2D". The procedure above is only an example. For details, see the television operating instructions. Wearing the 3D Eyewear If the 3D images are not displayed correctly, adjust the 3D image-related settings. * The perceived three dimensional effects of the 3D Eyewear differ from person to person. 1. (The indicator lamp will light for approximately 2 seconds, then flash once approximately every 2 seconds. ) 2. Put on the 3D Eyewear. NOTE · If the eyewear stops receiving infra-red signals from the television, the power automatically switches off after 5 minutes. If that happens, set the power switch to "OFF" then "ON" again. · For television settings, see the television operating instructions. After Use Set the 3D Eyewear power switch to "OFF". (The 3D Eyewear indicator lamp turns off, and the power turns off. ) After using the 3D Eyewear, store it in the case provided. 8 - ENGLISH Charging the 3D Eyewear Charging 1. Turn off the television power, and set the 3D Eyewear power switch to "OFF". Connect as shown in the diagram, and turn on the television power. · The indicator lamp lights red, and charging starts. Turn off the television power, and remove the charging cable. USB connector Mini USB connector NOTE · For the USB terminal, see the television operating instructions. [. . . ] *2 Viewing range The location of the 3D Eyewear transmitter differs depending on the model of television. There are differences in the viewing range of the 3D Eyewear among individuals. The 3D Eyewear may not operate correctly at the outside of the viewing range. Environment care information for users in China This symbol is only valid in China. ENGLISH - 13 Information on Disposal for Users of Waste Electrical & Electronic Equipment (private households) This symbol on the products and/or accompanying documents means that used electrical and electronic products should not be mixed with general household waste. [. . . ]