User manual PANASONIC TX-P50UT30B

[. . . ] Information for Users on Collection and Disposal of Old Equipment and used Batteries These symbols on the products, packaging, and/or accompanying documents mean that used electrical and electronic products and batteries should not be mixed with general household waste. For proper treatment, recovery and recycling of old products and used batteries, please take them to applicable collection points, in accordance with your national legislation and the Directives 2002/96/EC and 2006/66/EC. By disposing of these products and batteries correctly, you will help to save valuable resources and prevent any potential negative effects on human health and the environment which could otherwise arise from inappropriate waste handling. For more information about collection and recycling of old products and batteries, please contact your local municipality, your waste disposal service or the point of sale where you purchased the items. [. . . ] LMNOPQRST 4 l * 5 _ . !:# ghi pqrs (yellow) Store select 6 7 o 8 p 9 q !r : s # t mn Set characters (maximum : ten characters) User input BACK/ RETURN · To use numeric buttons set 1 4 7 abc jkl tuv 2 5 8 0 def mno wxyz 3 6 9 "Characters table for numeric buttons" (p. 92) 3 Store BACK/ RETURN · Channel position numbers (known as logical channel numbers) can be swapped in Channel List. To swap the channel position number [Channel List] (p. 49) Note Check DVB signal [Signal Condition] Selects a channel and checks the DVB signal condition. A good Signal Strength is not an indication of best signal for DVB reception. Please use the Signal Quality indicator as follows : [Signal Quality] : · Green bar Good · Yellow bar Poor · Red bar Bad (Check the Terrestrial aerial) Example : To change the channel DVB Signal Condition Channel Name Signal Quality Signal Strength Bit Error Rate Network Name Frequency Display a notification message [New Channel Message] Selects whether to give a notification message when a new DVB channel is found. Press EXIT to ignore. · 70 CBBC Channel 0 0 0. 00E+00 Wenvoe 802, 00 MHz, 64 QAM, 6940 kS/s 9 8 · Selecting OK will perform [Update Channel List]. 48 These bars show the maximum signal value of the selected channel. Skip unwanted DVB channels, Edit DVB Channels [Channel List] You can hide unwanted DVB channels. Select a channel and [reveal] / [hide] All DVB Channels · To reveal all channels select 70 CBBC Channel (yellow) 72 Cartoon Nwk [Reveal] / [Hide] 105 BBCi 719 720 1 7 BBC Radio Wales BBC Radio Cymru BBC ONE Wales BBC THREE : [Reveal] : [Hide] (skip) To edit channels You can also edit each channel in Channel List. Coronation Street 1 · To retune each channel [Manual the revealed47) (only for channels) BBC ONE WALES 20:00 - 20:55 Info Now (red) · To swap the channel position number (logical channel number) Store Enter the new position number (green) (green) abc jkl def ghi mno pqrs tuv wxyz 20:35 All DVB Channels Select favourites Update DVB channel automatically [Update Channel List] You can add new channels, delete removed channels, update channel name and position automatically to Channel List. Example : · Channel List is updated while keeping your settings in [Favourites DVB Update Channel List Edit], [Channel List], [Child Lock], [Timer Programming] etc. Progress CH 21 68 · Depending on the signal condition, the update may not work This will take about 3 minutes. CH Channel Name Type Quality Free TV: 0 Pay TV: 0 Radio: 0 Searching Data: 0 (Analogue) You can retune channels or skip unwanted channels, edit channels etc. 1 2 3 Select Analogue (p. 18) TV Tuning and Editing Channels Display the menu MENU Select [Setup] Main Menu Picture Sound Timer Setup select access 4 5 Select [Analogue Tuning Menu] select Analogue Tuning Menu Access access Select one of the following functions Analogue Tuning Menu Channel List Auto Setup Manual Tuning Access Access Access To return to TV EXIT select access · [Auto Setup] "Retuning from Setup Menu" (p. 46) 49 Skip unwanted Analogue channels, Edit Analogue channels [Channel List] You can hide unwanted Analogue channels. Select a channel and [reveal] / [hide] Analogue Channel List 1 2 3 4 5 6 7 BBC1 ***** ***** ***** ***** ***** ***** select [Reveal] / [Hide] : [Reveal] : [Hide] (skip) · To reveal all channels (yellow) To edit channels You can also edit each channel in Channel List. · To retune each channel ([Manual Tuning]) · To move the channel position (see below) Select the new position (red) (green) Store (green) · To rename the channel name (blue) Name Set characters (maximum : five characters) Edit channel name ABCDEFGH UVWXYZ a u b v c w d x e y f z g ( 0 h ) I 1 i + J 2 j K 3 k . LMNOPQRST 4 l * 5 _ . !:# ghi pqrs Store select BACK/ RETURN 6 7 o 8 p 9 q !r : s # t set mn 1 4 7 abc jkl tuv 2 5 8 0 def mno wxyz 3 6 9 · To use numeric buttons "Characters table for numeric buttons" (p. 92) Channel position Channel name 1 CH23 ITV 23:35 All Analogue Channels Tuning and Editing Channels · If a VCR is connected only with the RF cable, edit [VCR]. Set Analogue channel manually [Manual Tuning] [Fine Tuning] Use to make small adjustments to the tuning of an individual programme (affected by weather conditions, etc. ) Note [Manual Tuning] Set Analogue channel manually after Auto Setup. · If a VCR is connected only with the RF cable, it is recommended to select channel position [0]. Example : Analogue Manual Tuning 1 BBC1 Fine Tuning Manual Tuning CH33 CH 1 Store 99 H: 21 41 1 Select the channel position abc ghi pqrs jkl tuv def mno wxyz 2 Select the channel 3 Search 4 Select [Store] select store 50 Timer Programming Timer Programming from Menu The Timer Programming menu allows you to choose programmes that you wish to remind watching or record to the external recorder. At the correct time, the TV will tune to the correct channel automatically to record even if the TV is in Standby mode. [. . . ] · Take care not to subject the TV's surfaces to water or detergent more than requires. · Take care not to subject the surfaces to insect repellent, solvent, thinner or other volatile substances. · Take care not to tap or scratch the surface with your fingernail or other hard objects. · Do not allow the cabinet or pedestal to make contact with a rubber or PVC substance for a long time. This may degrade surface quality. Mains plug Wipe the mains plug with a dry cloth at regular intervals. [. . . ]