User manual PANASONIC TX-55CX700E

[. . . ] Retain your purchase receipt also, and note down the Model Number and Serial Number of your set in the space provided on the rear cover of these Instructions. AR/AS Coating on the Screen ( for TC-51P100G, TC-51P100H ) The Screen is coated with a special material to hinder ambient light reflection and dust adherence. The AR/AS coating may be observed when the set is switched off, since the coating give the screen surface a faint purplish or blue hue. Take care not to mark or scratch this coating. Important Information (1) The long time (max. 2 hours) use of TV game on the set is not recommended since the signal from TV game may be the cause of damage on picture projection tubes on the set. [. . . ] USA CATV Japan 22 ^ ^ GAME "SYS SELECT" Condition. The system select indicator will change as follows. CHINA HK/UK ASIA/M. EAST NZ/INDONES AUSTRALIA JAPAN CATV AMERICA SPECL VER E. EUROPE This returns the set to the normal viewing condition. Tuning Procedure Channel Allocation · CATV (USA CATV) channel numbers as recommended by the joint EIA/NCTA Engineering committee and published as EIA INTERIM STANDARD No. 6-CABLE TELEVISION CHANNEL IDENTIFICATION PLAN-MAY 1983. · The receiving channels are as follows; SYS SELECT CH DISPLAY 0 1 2 11 12 13 14 15 19 20 21 28 57 58 62 63 69 70 73 74 75 76 77 78 79 80 81 89 90 91 92 93 94 95 96 97 98 99 100 117 120 125 57 ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ Z1 Z9 Z10 Z11 Z12 Z13 Z14 Z15 Z16 Z17 Z18 Z19 Z20 Z37 ­ ­ ­ ­ CHINA ­ 1 2 12 13 HK/UK ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ 21 ASIA/M·E NZ/INDONES AUSTRALIA E·EUROPE SPECL VER AMERICA RECEIVE CHANNEL ­ ­ 0 ­ ­ ­ ­ 1 1 1 1 ­ 2 2 2 2 2 2 11 12 ­ ­ ­ ­ ­ ­ 21 11 ­ ­ ­ ­ ­ ­ ­ 21 11 12 ­ ­ 5A ­ 9A ­ 21 11 12 ­ ­ ­ ­ ­ ­ 21 11 12 13 ­ ­ ­ ­ ­ 21 CATV ­ 1 2 JAPAN ­ 1 2 12 13 13 14 62 63 69 ­ ­ ­ S'1 S'2 S'3 ­ ­ ­ S1 S2 S10 S11 S12 S13 S14 S15 S16 S17 S18 S19 S20 S21 62 63 69 ­ ­ ­ S'1 S'2 S'3 ­ ­ ­ S1 S2 S10 S11 S12 S13 S14 S15 S16 S17 S18 S19 S20 S21 62 63 69 ­ ­ ­ S'1 S'2 S'3 ­ ­ ­ S1 S2 S10 S11 S12 S13 S14 S15 S16 S17 S18 S19 S20 S21 62 63 69 E65 E69 S01 S02 S03 ­ ­ S1 S2 S10 S11 S12 S13 S14 S15 S16 S17 S18 S19 S20 S21 62 63 69 ­ ­ ­ S'1 ­ ­ ­ ­ ­ S1 S2 S10 S11 S12 S13 S14 S15 S16 S17 S18 S19 S20 S21 62 63 69 ­ ­ ­ S'1 S'2 S'3 ­ ­ ­ S1 S2 S10 ­ ­ ­ S14 S15 S16 S17 S18 S19 S20 S21 62 63 69 ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ ­ 62 63 62 C13 99 100 C49 ­ ­ ­ ­ ­ ­ ­ S41 ­ ­ S41 ­ ­ S41 ­ ­ S41 ­ ­ S41 ­ ­ S41 ­ ­ 125 23 Tuning Procedure Automatic Tune (Channel Select and Regional System must already be set; Refer to pages 20 to 23) 1, 6 2, 4 3 DISPLAY TV/AV PRE. - + (TV set) This TV uses automatic tuning to determine whether or not a broadcast signal is being sent which it can receive, and automatically prepares so that the channel selection can respond to both the position select and direct select modes. 1 PRE. Push the "PRE. " (PRESET) button 3 times. 1 CH1 2 + Push the Volume Up "+" or Down "-" button. 3 After all stations are tuned, the on-screen display will automatically change from "AUTO TUNE" to "SOUND SYS" Position. Confirm the sound condition of each Programme Number by using the Programme Number Up "" button. 2 CH2 4 + I f n e c e s s a r y, p u s h t h e Volume Up "+" or Down "-" button, to improve the Sound quality. 2 CH2 24 ^ ^ GAME Automatic Search "AUTO TUNE" Condition. Search Start. The best tuning position is automatically memorized. If the Sound is not clear or no sound is produced on a Programme Number, then follow the next Step 4. Note: When sound volume is too small to confirm, turn it up by using the sound volume button on the remote control. The sound indicator will change as follows. 4. 5MHz 6. 5MHz 5. 5MHz 6. 0MHz Tuning Procedure 5 3 4 Use the Programme Number Up "" button to sequentially check each station. If necessary, repeat steps 3 to 4 for each Programme Number. 6 PRE. After all stations are tuned, push the "PRE. " (PRESET) button 4 times. This returns the set to the normal viewing condition. Programme Number memory locations. Helpful Hint (1) To tune, push the Main Menu button and Position button on the Remote Control. By following the display in the Preset Menu, setting can be formed using only the Remote Control. (2) If a clear picture with correct colours cannot be obtained when a Broadcast or AV signal is received, refer to the "Colour System Selection" operation on page 35. (3) After the Automatic tune is finished, push the Programme Number "" button to confirm the tuning condition for each Programme Number. If some Programme Numbers are unused, it is possible to skip such Programme Numbers. REVEAL F/T/B 4 + + 32 ^ 8 1 2 ^ ^ Programme Number Selection Push the Programme Number Up "" or Down "" button to select the next higher or lower Programme number. Direct Programme Number Selection (CH SELECT = POS. ) You can select the numbers directly by pushing "Number 0-9" button and the two digit Numbers by pushing "Two Digit" and "Programme Number" buttons. 8 2 Programme Number 12. . . . . . , 1, 2 Direct Programme Number Selection (CH SELECT = DIRECT) You can select the number directly by pushing the corresponding programme number button. 1 , 2 , 4 Note: When the Skip setting for Programme Number 100 through 125 is on, the channel selection time will be shortened, and thus you can not input three digits at a time. Volume adjustment Push the Volume Up "+" or Down "-" button to increase or decrease the sound volume level. General Operation 5 TV/AV TV/AV TV/AV mode Selection Push the "TV/AV" button to select TV, AV1, AV2, AV3, AV4 input signal modes sequentially. 9 + Recall button Push the "Recall" button to display the current system status. Push again to cancel. 4 6 DISPLAY Display button By pushing the Display button various demonstrations and on screen displays will appear. Push the Display button a second time to halt the display/demonstration mode, and return the set to the normal viewing condition. Note: When this button is pushed, the Picture and Sound Menus change to Picture (DYNAMIC) and Sound (DYNAMIC). S-DYNAMIC P-DYNAMIC 30 Programme Number (Refer to page 20) Audio Mode (Refer to page 41) Sound Menu (Refer to page 43) Picture Menu (Refer to page 42) Off Timer (Refer to page 33) 7 GAME Game button Push this button to change to the AV2 input signal and enter Game mode. Note: When you push this button during stand-by mode, the TV will turn on automatically and the picture and sound changes to a suitable mode for video games. 10 Off Timer button The TV set may be preset to switch to stand-by after a fixed period. By pushing "Off-Timer" button, you can select the preset time; either "30", "60", "90" minutes or AUTO mode. 30 60 0 90 AUTO 8 Sound Mute button Push this button to mute the sound completely. If the set is not switched off when the TV station stops broadcasting, it will automatically go to Stand-by mode after 5 minutes. Note: Off-Timer setting will not operate in AUTO mode when the Television set is in AV mode. Push the button once again to restore the previous sound level, and cancel the mute. 33 General Operation Sound System Selection (Different region use differing systems) 1, 3 2 DISPLAY TV/AV PRE. - + (TV set) This function is used only in the TV mode, and is not applicable in AV mode when the sound is not clear or no sound is produced on a Programme Number. 1 PRE. Push the "PRE. " (PRESET) button 5 times. 2 CH2 2 + Push the Volume Up "+" or Down "-" button repeatedly until the optimum sound is obtained. 2 CH2 3 PRE. Push the "PRE. " (PRESET) button 4 times. 34 ^ ^ GAME Sound System Condition. The sound system will change as shown. 4. 5MHz 6. 5MHz 5. 5MHz 6. 0MHz Note: These are different sound broadcast transmission systems applicable to differing countries. [. . . ] To select page 6 enter 0, 0, 0 and 6. VCR/LD/DVD 0 VCR LD/DVD A DISC SIDE B 6 MAIN MENU SKIP N SKIP 3 TIME TEXT Push the TIME TEXT button. TV/TEXT TIME TEXT INDEX HOLD F. P. REVEAL F/T/B 1 3 52 Teletext Operation TEXT Menu Operation MAIN MENU 1. Push the "TV/TEXT" button on the Remote Control to select the TEXT mode. Select the "TEXT" menu by pushing the Position Up "" or Down "" button and Access the "TEXT" menu by pushing the Position Left "<" or Right ">" button. Choose the option and adjust by pushing the Position Up "" or Down "" buttons, and by setting with the Position Left "<" or Right ">" buttons. DISPLAY CANCEL Push the Position Left "<" or Right ">" button to view the TV picture whilst searching for a Teletext page. [. . . ]