User manual PANASONIC SC-HC25DBEB

[. . . ] SAFETY PRECAUTIONS Operating Instructions Placement Set the system up on an even surface away from direct sunlight, high temperatures, high humidity, and excessive vibration. These conditions can damage the cabinet and other components, thereby shortening the service life of the system. Place it at least 15 cm away from wall surfaces to avoid distortion and unwanted acoustical effects. Do not place heavy items on the system. Sales and Support Information Customer Care Centre · For customers within the UK: 0844 844 3852 · For customers within Ireland: 01 289 8333 · Visit our website for product information www. panasonic. co. uk · E-mail: customer. care@panasonic. co. uk Direct Sales at Panasonic UK · For customers: 0844 844 3856 · Order accessory and consumable items for your product with ease and confidence by phoning our Customer Care Centre Monday­Thursday 9:00 a. m. ­ 5:30 p. m. , Friday 9:30 a. m. ­ 5:30 p. m. [. . . ] Press [CD x, OPEN/CLOSE] again to close the sliding door. 1 Press [PROGRAM] in the stop mode. "PGM" is shown. When other Panasonic equipment respond to the remote control of this system, change the remote control code of this system. To set the code to "REMOTE 2" 1 Press and hold [RADIO, EXT-IN] on the main unit and [1] on the remote control until "REMOTE 1" is shown. 4 seconds. 2 Press and hold [OK] and [1] for a minimum of 2 Press the numeric buttons to select the desired track. Click! 1 Press and hold [RADIO, EXT-IN] on the 3 Press [4/9] to start playback. 3 Press [6] and then press the numeric buttons to select the desired track. 8 main unit and [2] on the remote control until "REMOTE 2" is shown. 4 seconds. CLOCK AND TIMERS 1 Press [CLOCK/TIMER] to select "#PLAY 1", "#PLAY 2" or "#PLAY 3". start time. 2 Press and hold [OK] and [2] for a minimum of Setting the clock This is a 24-hour clock. 2 Press [CD] and then press [4/9] to start 2 Within 10 seconds, press [R, T] to set the 3 Press [OK]. 4 Do steps 2 and 3 again to set the end time. To start the timer playback. 2 Within 10 seconds, press [R, T] to set the time. 12 TROUBLESHOOTING GUIDE Stop playback Pause playback Skip album Skip track Search through track 4 Press [OK]. Do steps 2 through 4 again to program other tracks. To check while programming, press [PROGRAM] two times after "PGM" is shown, then press [2] or [6]. Within 5 seconds, press [8] again. 5 Press [4/9] to start playback. Cancel program mode Replay the program Check program contents 3 Press [OK]. Press [CLOCK/TIMER] to show the clock for a few seconds. Note: Reset the clock regularly to maintain accuracy. Before requesting service, make the following checks. If you are in doubt about some of the check points, or if the solutions indicated do not solve the problem, consult your dealer for instructions. 5 Press [#, PLAY] to start "#PLAY 1", "#PLAY 2" or "#PLAY 3". Common problems No operations can be done with the remote control. · Switch off the system, determine and correct the cause, then switch the system on again. It can be caused by straining of the speakers through excessive volume or power, and when using the system in a hot environment. Keep other appliances and cords away from the cables of this system. Main unit displays "NO PLAY" · Examine the content. · This system can read and play up to 255 albums or folders (audio and non-audio). "F76" or "F61" · There is a power supply problem. "VBR­" · The system cannot show the remaining play time for variable bit rate (VBR) tracks. "DATA" · Data broadcast being received over the DAB broadcast signal, cannot be used on this system. "SCRAMBLED" · The broadcast station being received cannot be accessed. "NO SERVICE" · The station is currently not broadcasting. [. . . ] "DAB AUTO SCAN" is shown. 5 USING AN iPod OR iPhone Pause playback Skip track Search the current track View iPod or iPhone menu, Return to previous menu Select an iPod or iPhone menu item Press [4/9] or [8]. Press [iPod MENU] in the play mode. 2 Press [OK]. You can connect and play MP3 tracks from your USB mass storage device. The system cannot recognize USB mass storage device connected through a cable. 2 While you press and hold [1] on the main 3 Release [1]. Using the auxiliary input You can connect a portable audio equipment and listen to the audio through this system. Preparation Switch off the equalizer (if any) of the portable audio equipment to prevent sound distortion. [. . . ]