User manual PANASONIC SC-HC15EB

[. . . ] SAFETY PRECAUTIONS Operating Instructions Placement Set the system up on an even surface away from direct sunlight, high temperatures, high humidity, and excessive vibration. These conditions can damage the cabinet and other components, thereby shortening the service life of the system. Place it at least 15 cm away from wall surfaces to avoid distortion and unwanted acoustical effects. Do not place heavy items on the system. Information for Users on Collection and Disposal of Old Equipment and used Batteries These symbols on the products, packaging, and/or accompanying documents mean that used electrical and electronic products and batteries should not be mixed with general household waste. [. . . ] REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. CAUTION! THIS PRODUCT UTILIZES A LASER. USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. The socket outlet shall be installed near the equipment and easily accessible. The mains plug of the power supply cord shall remain readily operable. To completely disconnect this apparatus from the AC Mains, disconnect the power supply cord plug from AC receptacle. "VBR­" · The system cannot show the remaining play time for variable bit rate (VBR) tracks. "NODEVICE" · The USB mass storage device is not connected. Examine the connection. Playing discs Manual tuning Changing the sound quality Memory reset (Initialisation) 1 Press [CD x, OPEN/CLOSE] on the main unit to open the sliding door. Press [CD x, OPEN/CLOSE] again to close the sliding door. 1 Press [RADIO, EXT-IN] to select "FM" or "AM". 1 Press [PROGRAM] in the stop mode. "PGM" is shown. 1 Press [SOUND] to select a sound effect. BASS TREBLE SURROUND INPUT LEVEL (For AUX source) -4 to +4 2 Press [3] or [5] to select the frequency of the required station. To tune automatically, press and hold the button until the frequency starts changing quickly. 2 Press the numeric buttons to select the desired track. Click! 1 Press [OK] to select "LOWEST" or "CURRENT" frequency. To cancel, press [8]. When the following situations occur, refer to the instructions below to reset the memory: · There is no response when buttons are pressed. · You want to clear and reset the memory contents. To reset the memory 2 Press [AUTO PRESET] to start presetting. Manual presetting 30 FM and 15 AM stations can be preset. 1 Disconnect the AC mains lead. 3 Press [4/9] to start playback. 3 Press [6] and then press the numeric buttons to select the desired track. To improve the sound quality When "FM" is selected (Wait 3 minutes before you continue with step 2. ) unit, connect the AC mains lead again. "­ ­ ­ ­ ­ ­ ­ ­" shows on the display panel. D. BASS This function lets you enjoy a powerful bass effect. Press [D. BASS] to select "ON D. BASS" or "OFF D. BASS". 2 While you press and hold [1] on the main 3 Release [1]. 2 Press [CD] and then press [4/9] to start 1 Press [RADIO MENU] to select "FM MODE". To cancel, select "STEREO". · "MONO" is also cancelled when you change the playback. Press [R, T]. Preparation Press [RADIO, EXT-IN] to select "FM" or "AM". 1 Press [3] or [5] to tune in to the station. All the settings are set back to the factory preset. It is necessary to set the memory items again. Stop playback Pause playback Skip album Skip track Search through track 4 Press [OK]. Do steps 2 through 4 again to program other tracks. frequency. · Turn off "MONO" for normal listening. 5 Press [4/9] to start playback. Cancel program mode Replay the program Check program contents Press [PROGRAM] in the stop mode. To check while programming, press [PROGRAM] two times after "PGM" is shown, then press [2] or [6]. [. . . ] · Switch off the system, determine and correct the Radio A beat sound is heard. · Set to "BP 1" or "BP 2" when in AM tuner mode. · Move the antenna away from other cables and cords. 5 Press [#, PLAY] to start "#PLAY 1", "#PLAY 2" or "#PLAY 3". 6 Press [`] to switch off the system. Change the settings Change the source or volume The system must be switched off for the timer to operate. 1) Press [#, PLAY] two times to remove the timer indicator on the display panel. [. . . ]