User manual PANASONIC PAWDHWM200A

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual PANASONIC PAWDHWM200A. We hope that this PANASONIC PAWDHWM200A user guide will be useful to you.


PANASONIC PAWDHWM200A : Download the complete user guide (9141 Ko)

You may also download the following manuals related to this product:

   PANASONIC PAWDHWM200A (9035 ko)
   PANASONIC PAWDHWM200A (9035 ko)
   PANASONIC PAWDHWM200A (9035 ko)
   PANASONIC PAWDHWM200A (9131 ko)
   PANASONIC PAWDHWM200A (9131 ko)
   PANASONIC PAWDHWM200A (9131 ko)
   PANASONIC PAWDHWM200A (9131 ko)
   PANASONIC PAWDHWM200A (9035 ko)
   PANASONIC PAWDHWM200A (9035 ko)
   PANASONIC PAWDHWM200A (9131 ko)

Manual abstract: user guide PANASONIC PAWDHWM200A

Detailed instructions for use are in the User's Guide.

[. . . ] T  he connection of the heat pump to the power supply must be performed in accordance with the standards for electrical installations. An appliance for the disconnection from the electrical network must be installed between the heat pump and the electrical network in accordance with the national installation regulations. I n avoidance of aggregate damage the heat pump must not operate without water in the tank. T  he installation should be performed in accordance with the valid regulations and the instructions of the manufacturer. [. . . ] The condensate should be drained to the sewage system via flexible tube Ø16mm on the rear side of the heat pump. The quantity of condensate depends on air temperature and humidity or air. Figure 6: Connection to water supply mains – condensate outlet 543151 44 To reduce noise and vibrations of the installed fan take the following steps to prevent the noise and vibrations to be transmitted through walls into rooms, where it would be disturbing (bedrooms, restrooms): • install flexible connectors for hydraulic jacks • install flexible pipes for air inlet and outlet • isolate the vibrations for wall transmitters • provide silencers for air inlet and outlet • air inlet and outlet pipes attach with vibration silencers • predict isolation of vibrations via flor • use support elements. CONNECTION TO WATER SUPPLY MAINS Connect the water pipeline system according to the attachment signs from the previous chapter. Installing a safety valve is mandatory in order to assure safe operation. The valve prevents an increase of the pressure in the boiler by any more than 0. The outflow nozzle on the safety valve must have an outlet into the atmosphere. To assure correct operation of the safety valve, check the valve regularly and, if necessary, remove the limescale and check that the safety valve is not blocked. When checking the valve, push the lever or unscrew the nut of the valve (depending on the type of the valve) and open the drain from the safety valve. Water must flow from the valve nozzle, showing that the valve operation is faultless. During the heating of water, the water pressure in the hot water tank is increased up to the level present in the safety valve. If trying to start up at a lower temperature, please see chapter "Operation at lower temperatures". The appliance stops functioning and the only field visible on the screen is field no. (If you switch off the heat pump for a longer period of time, the water must be drained from the pump if there is any danger of freezing). Power failure protection In case of power failure, the settings remain stored for up to 23 hours. After restarting, the heat pump operates in the same mode it was operating in before the power failure. Operation at lower temperatures When the appliance is switched on, the fan starts first and operates for one minute (symbol no. If the temperature of inlet air is lower than -7 °C, the fan is turned off. The possibility of switching to normal mode is checked every 2 hours by switching on the fan for one minute. If the temperature of inlet air is higher than -7 °C, the heat pump switches to normal mode of operation (symbols 16 and 20 are displayed). 47 543151 EN 10 Increasing the value At lower air temperatures, the evaporator defrosting cycle is started if necessary. Defrosting takes place until the conditions for normal operation of the heat pump are achieved. [. . . ] € The antilegionelle cycle is performed regardless the state of the PV mode. PV operation (activated): • PV is activated and the operation of the heat pump is allowed. The heat pump heats the water to the maximum temperature (see technical characteristics table). € No contact between PV clamps and the heat pump operation is allowed. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE PANASONIC PAWDHWM200A




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual PANASONIC PAWDHWM200A will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.